Question

In: Physics

My physics teacher explained the difference between voltage and current using sandwiches. Each person gets a...

My physics teacher explained the difference between voltage and current using sandwiches. Each person gets a bag full of sandwiches when they pass through the battery. Current = the number of people passing through a particular point per unit time. Voltage = the (change in) number of sandwiches per person. In a parallel circuit the number of people (current) is divided between the two paths, but the number of sandwiches per person (voltage) remains the same. In a series circuit the number of people passing through a particular point remain the same, but they drop off a certain percentage of their sandwiches at every resistor. Therefore, there is a voltage drop that occurs between the points before and after every resistor.

This analogy naturally leads to the question: how do the electrons "know" that they are going to have to share their voltage between two resistors before they reach the second one? (In other words, not drop off all their sandwiches at the first resistor they find)

Solutions

Expert Solution

These laws are based on a circuit in equilibrium. If you made a circuit where you had +1 volt on the left, 1 ohm in the middle, and +2 volts on the right, and you started out with the resistor not under any voltage, electricity would start out moving towards the center of the resistor until it builds up a voltage of about 1.5 volts. (It would gradually change from 1 volt to two based on which source you're closer to.)

If you want to extend the sandwich analogy, imagine, for some reason, that the strength of people is proportional to their sandwiches. They also have no idea where they're going, and they push at random. And the number of sandwiches they drop is proportional to their speed.

In my circuit, at first people will be pushed by the people behind them, until they get to the center. At this point, the guys on the right have more sandwiches, so they shove the people on the left back, until you end up with just a group of people going from the right to the left. They're slowed down exactly enough to have one sandwich at the end, since if they went slower, they'd have more sandwiches than the guys they're pushing against, speeding them up. If they went faster, they'd have fewer, slowing them down.

The reason you always end up with everyone having the same number of sandwiches when they meet at a node is if they don't, the guys with more sandwiches push back on the guys with less, slowing them down, until they end up having the same number of sandwiches. It might be off for a little bit, but it will quickly enter an equilibrium.


Related Solutions

what is the phase difference in phase angle between induced voltage and current in a PMSM...
what is the phase difference in phase angle between induced voltage and current in a PMSM controlled to keep maximum torque per amp?
1)Why is there phase difference between voltage and current in an a.c. circuit ?. Explain the...
1)Why is there phase difference between voltage and current in an a.c. circuit ?. Explain the concept of power factor. 2). Discuss the disadvantages of a low power factor. 3. Explain the causes of low power factor of the supply system. 4. Discuss the various methods for power factor improvement 5)Write short notes on the following : (i) Power factor improvement by synchronous condenser (ii) Importance of p.f. improvement (iii) Economics of p.f. improvement
what is difference between applied physics and physical engineering?
what is difference between applied physics and physical engineering?
l. what is the difference between a real independent voltage source and an ideal independent voltage...
l. what is the difference between a real independent voltage source and an ideal independent voltage source? Give an example of a real voltage source and explain how it differs from the ideal. 2. What does it mean when we say that a circuit containing multiple sources is invalid?Give an example of such a circuit and explain why it is invalid. 3. What is resistance? What is a node? What is a closed loop? 4. Write the equations for Ohm's...
what is the main difference between voltage source and voltage load? use sketches where suitable.
what is the main difference between voltage source and voltage load? use sketches where suitable.
Producer Surplus is defined as the difference between what a seller of a good gets and...
Producer Surplus is defined as the difference between what a seller of a good gets and his cost of selling the good. If the hypothetical kidney market turned out to be like the one illustrated in Question #4 above, what would be the approximate total producer surplus realized by the sellers of kidneys? Price (In dollars) Quantity Demanded $100,000 50,000 90,000 55,000 80,000 60,000 70,000 65,000 60,000 70,000 50,000 75,000 40,000 80,000 30,000 85,000 20,000 90,000 10,000 95,000 0 100,000...
QUESTION 2. 2.1 What is the difference between a natural person and a legal person 2.2...
QUESTION 2. 2.1 What is the difference between a natural person and a legal person 2.2 briefly explain what you understand by the docttrine of stare decsis
When a voltage difference is applied to a piece of copper wire, a 5.0 mA current flows.
When a voltage difference is applied to a piece of copper wire, a 5.0 mA current flows. If the copper wire is replaced with a silver wire with twice the diameter of the copper wire, how much current will flow through the silver wire? The lengths of both wires are the same, and the voltage difference remains unchanged. (The resistivity of copper is 1.68 × 10-8 Ω·m, and the resistivity of silver is 1.59 × 10-8 Ω ·m)a. 1.3 mAb. 19 mAc....
Consider the three basic quantities of a circuit: voltage (potential difference), current, and resistance. In general...
Consider the three basic quantities of a circuit: voltage (potential difference), current, and resistance. In general terms, describe each one in your own words and its basic characteristic/property, and can you do an analogy of these quantities with a fluid system, say a stream of water? Further, since many of you are in the medical field, can you relate a basic circuit and its components to a system of the body, maybe the circulatory system? If, what is the analogy...
What is the difference between energy and matter when it gets processed through a system? How...
What is the difference between energy and matter when it gets processed through a system? How do different species interact with each other? (relationships between organisms like competition, etc…) What are some of the major threats to the biosphere and why is conservation biology important?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT