Question

In: Physics

A fire hose has an inside diameter of 6.40 cm. Suppose such a hose carries a...

A fire hose has an inside diameter of 6.40 cm. Suppose such a hose carries a flow of 40.0 L/s starting at a gauge pressure of 1.62×106N/m2 . The hose goes 10.0 m up a ladder to a nozzle having an inside diameter of 3.00 cm. Calculate the Reynolds numbers for flow in the fire hose and nozzle to show that the flow in each must be turbulent.

Solutions

Expert Solution


Related Solutions

Fire hoses used in major structural fires have an inside diameter of 6.40 cm. Suppose such...
Fire hoses used in major structural fires have an inside diameter of 6.40 cm. Suppose such a hose carries an inital flow of 40.0 L/s at ground level, starting at a gauge pressure of 1.62 x 106 N/m2. The hose rises up 10.0 m along a ladder to a nozzle having an inside diamter of 3.00 cm. (Hint use Bernoulliʻs equation) 1)Draw a diagram of what is happening? 2)What is the speed at v1 and v2 in m/s? 3)What is...
Filling a Swimming Pool with a Garden Hose A 1/2 in. (inside) diameter garden hose is...
Filling a Swimming Pool with a Garden Hose A 1/2 in. (inside) diameter garden hose is used to fill a round swimming pool 7.18 m in diameter. How many days will it take to fill the pool to a depth of 1.52 m if water issues from the hose at a speed of 0.258 m/s? You do not need to enter the units.
A hose with a diameter of 1.6 cm is used to fill a pool (circular in...
A hose with a diameter of 1.6 cm is used to fill a pool (circular in shape) of 6 m in diameter. How long will it take for the water in the pool to reach a depth of 1.4 m, knowing that the water flows at a speed of 0.40 m/s? *Demonstrate all algebraic procedures*
. A steam main (outside diameter of 16.8 cm and inside diameter of 15.4 cm) is...
. A steam main (outside diameter of 16.8 cm and inside diameter of 15.4 cm) is covered with 5-cm of high temperature insulation (k = 0.095 W/m. K) and 3.8 cm of lower temperature insulation (k = 0.07W/m. K). Calculate the heat loss from 150 m pipe assuming that inner and outer surface temperatures of the insulation are 450 and 30 °C, respectively. Also determine the temperature at the interface between two layers of insulation (10 points).
A garden hose with an internal diameter of 2.7 cm is connected to a (stationary) lawn...
A garden hose with an internal diameter of 2.7 cm is connected to a (stationary) lawn sprinkler that consists merely of a container with 26 holes, each 0.33 cm in diameter. If the water in the hose has a speed of 0.86 m/s, at what speed does it leave the sprinkler holes?
To water the yard, you use a hose with a diameter of 3.1 cm. Water flows...
To water the yard, you use a hose with a diameter of 3.1 cm. Water flows from the hose with a speed of 1.5 m/s. If you partially block the end of the hose so the effective diameter is now 0.55 cm, with what speed does water spray from the hose?
A water hose 2.85 cm in diameter is used by a gardener to fill a 28.0-liter...
A water hose 2.85 cm in diameter is used by a gardener to fill a 28.0-liter bucket. (One liter = 1,000 cm3.) The gardener notices that it takes 1.00 min to fill the bucket. A nozzle with an opening of cross-sectional area 0.500 cm2 is then attached to the hose. The nozzle is held so that water is projected horizontally from a point 1.00 m above the ground. Over what horizontal distance can the water be projected? 4.33 m *CORRECT*...
A uniformly charged disk of radius 35.0 cm carries a charge density of 6.40 ✕ 10-3...
A uniformly charged disk of radius 35.0 cm carries a charge density of 6.40 ✕ 10-3 C/m2. Calculate the electric field on the axis of the disk at the following distances from the center of the disk. (a) 5.00 cm MN/C (b) 10.0 cm MN/C (c) 50.0 cm MN/C (d) 200 cm MN/C
A garden hose with a diameter of 1.8 in. has water flowing in it with a...
A garden hose with a diameter of 1.8 in. has water flowing in it with a speed of 0.57 m/s and a pressure of 1.3 atmospheres. At the end of the hose is a nozzle with a diameter of 0.54 in. Part A) Find the speed of the water in the nozzle. Part B) Find the pressure in the nozzle.
A long solenoid (1500 turns/m) carries a current of 20 mA and has an inside diameter...
A long solenoid (1500 turns/m) carries a current of 20 mA and has an inside diameter of 4.0 cm.  A long wire carries a current of 2.0 A along the axis of the solenoid.  What is the magnitude of the magnetic field at a point that is inside the solenoid and 1.0 cm from the wire? a. 78 µ b.   55 µT c.    48 µT d.   68 µT e.   2.0 µT
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT