Question

In: Mechanical Engineering

A solid square rod is cantilevered at one end. The rod is 0.8 m long and...

A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of ±1.3 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 3 × 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end.
Is the initial estimate of the size modification factor 0.85 adequate?

Multiple Choice

No

or

Yes

Solutions

Expert Solution


Related Solutions

One end of a uniform ℓ = 4.40-m-long rod of weight w issupported by a...
One end of a uniform ℓ = 4.40-m-long rod of weight w is supported by a cable at an angle ofθ = 37°with the rod. The other end rests against a wall, where it is held by friction (see figure). The coefficient of static friction between the wall and the rod isμs = 0.595.Determine the minimum distance x from point Aat which an additional weight w (the same as the weight of the rod) can be hung without causing the...
An aluminum rod with a square cross section is 1.2 m long and 5.0 mm on...
An aluminum rod with a square cross section is 1.2 m long and 5.0 mm on edge. (a) What is the resistance between its ends? (b) What must be the diameter of a cylindrical copper rod of length 1.2 m if its resistance is to be the same as that of the aluminum rod? The resistivity of aluminum is 2.75 × 10-8 Ω·m and the resistivity of copper is 1.69 × 10-8 Ω·m.
A steel rod 0.450 m long and an aluminum rod 0.250 m long, both with the...
A steel rod 0.450 m long and an aluminum rod 0.250 m long, both with the same diameter, are placed end to end between rigid supports with no initial stress in the rods. The temperature of the rods is now raised by 60.0 ∘C. What is the stress in each rod? (Hint: The length of the combined rod remains the same, but the lengths of the individual rods do not.) Psteel,Paluminium = ?
1.) A 1.00m long, 5.00kg rod is held at one end. How much torque is generated...
1.) A 1.00m long, 5.00kg rod is held at one end. How much torque is generated by the bar? What happens to the torque if the mass remains consant but the length is doubled? 2.) A large light (2.00kg) is held away from a wall by a 50.0cm rod (massless) and a cable that attaches to the wall at a 45 degree angle. Find the forces provided by the wall and the cable on the rod.
A heat conducting rod, 1.60 m long, is made of an aluminum section, .9 m long,...
A heat conducting rod, 1.60 m long, is made of an aluminum section, .9 m long, and a copper section, .7 m long. both sections have a cross-sectional area of .0004 m2. the aluminum end and the copper end are maintained at temperatures of 30 degrees celcius and 170 degrees celcius, respectively. the thermal conductivity of aluminum and copper are 205 and 385 W/m*K, respectively. the rate at which heat is conducted in the rod is closest to: 11W 12W...
A straight rod of solid polymer is of length 1 m and diameter 10 mm. The...
A straight rod of solid polymer is of length 1 m and diameter 10 mm. The polymer is linearly viscoelastic with a tensile creep compliance given by: D = 2- exp(-0.1t); Gpa^-1 Where t is in hours. The rod is suspended vertically and a mass of 10 kg is hung from it for 10 hours. a) Find the change of length of the rod. b) Identify the time domain of this property test procedure.
The left end of a long glass rod 8.60 cm in diameter, with an index of...
The left end of a long glass rod 8.60 cm in diameter, with an index of refraction 1.55, is ground and polished to a convex hemispherical surface with a radius of 4.30 cm . An object in the form of an arrow 1.53 mm tall, at right angles to the axis of the rod, is located on the axis 23.5 cm to the left of the vertex of the convex surface. Find the height of the image of the arrow...
A 0.25 kg block slides down a ramp that is 0.6 m tall, 0.8 m long...
A 0.25 kg block slides down a ramp that is 0.6 m tall, 0.8 m long and has a diagonal length of 1.0 m. The block starts at rest and arrives at the bottom with a speed of 1.3m/s. a.) How much heat was created by friction? b.)What is the average frictional force acting on the block? At what rate is kinetic energy being dissipated into heat near the bottom of the ramp? c.)Instead of a block, a cart with...
A nuclear fuel element is in the form of long solid cylindrical rod (k=0.85 W/mK) of...
A nuclear fuel element is in the form of long solid cylindrical rod (k=0.85 W/mK) of diameter 14 mm is generating heat at an uniform rate of 0.45×108 W/m3 because of nuclear fission. Heat is transfer to pressurized cooling water at 300 0C and surface heat transfer coefficient is 4500 W/m2k. calculate the maximum temperature in the fuel rod in the system. What is the change in Tmax if the fuel element is encapsulated in a thin metal cladding of...
Its mass of 1.5 m long, one end of which is tied to the ceiling of...
Its mass of 1.5 m long, one end of which is tied to the ceiling of the room, is negligible, and a small object with a mass of 0.75 kg is hung on the free end of an inelastic rope. This object makes a circular motion at a speed of 25 rad / s, making an angle of 30 ° with the vertical. a1) What is the rotational kinetic energy of this object? a2) What is the rotational kinetic energy...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT