Question

In: Mechanical Engineering

A beam of steel having square cross section of 20x20mm2 having E = 200 GPa is...

A beam of steel having square cross section of 20x20mm2

having E =
200 GPa is subjected to an axial (P) load of 20 kN, Torsional (T) load
of 60 Nm and Transverse (F) load of 0.60 kN as shown in Figure. Solve
each load independently for both element A and B existing at the top
and side surface of the beam respectively and determine:
a) State of stress against each load condition for both element A
and B
b) Draw Mohr’s Circle where applicable for each state of stress for
both element A and B
c) Determine the principal planes and the principal stresses,
d) Draw the orientation of the Principal Stresses
e) The stress components exerted on the element obtained by
rotating the given element counterclockwise through 30
degrees.

Solutions

Expert Solution

A thumbs up, pls !!


Related Solutions

A reinforced concrete beam has square cross section (h × h). There are 9 steel reinforcing...
A reinforced concrete beam has square cross section (h × h). There are 9 steel reinforcing bars (each of diameter ds), 3 evenly spaced towards the top, 3 along the neutral axis, and 3 evenly spaced towards the bottom. The vertical distance from the centre of the bar to top (or bottom) edge of the section is called the cover, and is denoted as e. It should be taken that ρsteel = 7850 kg/m3, ρconcrete = 2350 kg/m3, Econcrete =...
What A laminated steel (E = 200 GPa and ? = 0.3) cylinder consists of a...
What A laminated steel (E = 200 GPa and ? = 0.3) cylinder consists of a jacket with an inside diameter of 200 mm and an outside diameter of 300 mm shrunk onto a tube with an inside diameter of 100 mm. The initial shrinkage pressure is 25 MPa. Determine: a. The maximum tensile stress in the cylinder after it is fabricated subject to an internal pressure of 200 MPa. b. What and where is the maximum shear stress?
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M of all types of beam diagram of the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
Determine the location of the shear centre of the C-shaped rolled-steel beam cross-section C150x19.3 with respect...
Determine the location of the shear centre of the C-shaped rolled-steel beam cross-section C150x19.3 with respect to the centre of the web. Indicate whether it is to the left or right of the centre of the web. Assume the section to be thin walled and neglect the rounding of corners.
A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm × 3.0 mm...
A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm × 3.0 mm (0.7520 in. × 0.1181 in.) has the stress-strain behavior shown in the Animated Figure 6.22. If this specimen is subjected to a tensile force of 95120 N (21380 lbf) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 590 mm, what will be its final length after this force is...
10 cm of copper with square cross section of 1x1 cm exposed to 200 KN tension...
10 cm of copper with square cross section of 1x1 cm exposed to 200 KN tension force caused 15% permanent reduction in cross section area , if the fracture got on this point, calculate the following: 1 – the ductility 2 – stress 3 – true stress 4- fracture stress
The steel beam has the cross section shown. The beam length is L = 6.9 m, and the cross-sectional dimensions are d = 345 mm, bf = 185 mm, tf = 15 mm, and tw = 10 mm.
The steel beam has the cross section shown. The beam length is L = 6.9 m, and the cross-sectional dimensions are d = 345 mm, bf = 185 mm, tf = 15 mm, and tw = 10 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 185 MPa.
An accelerator produces a beam of protons with a circular cross section that is 1.6 mm...
An accelerator produces a beam of protons with a circular cross section that is 1.6 mm in diameter and has a current of 1 mA. The current density is uniformly distributed throughout the beam. The kinetic energy of each proton is 20 MeV. The beam strikes a metal target and is absorbed by the target. 1) What is the number density of the protons in the beam? 2) How many protons strike the target in each minute? 3) What is...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT