procedure of fabrication and erection of structural steel works in oil and gas field

Environmental law means the laws that regulate the impact of human activities
on the environment which covers a broad range of activities that affect air,
water, land, flora or fauna. It includes laws that relate to land use and
development, pollution, waste management, climate change, emissions and
water resource management. Conclude SIX (6) general functions of most
environmental laws.

A brick laid its greatest dimension horizontal and its face parallel to the wall face called

A)Shiner

B) Plasticity

C) Strength

D) All of the above

Grouting brick or CMU wall serves to

1. Increase the cross sectional area of the wall
2. Resist vertical and lateral shear loads
3. Bonds wythes together

D. All of the above

1.What are the criteria for classifying a confined space as a permit required confined space? Include the citation for the OSHA standard where you found the answer to the question.

a) differentiate quality from quality assurance.

b) Suppliers should be chosen with the sole aim of maximum value for the company. Courtesy and equitable dealings with sales representatives create goodwill and establish. State and explain six categories of electronic commerce business models that could be used.

c) If standards are to be maintained in the Industry it is essential that those associated with construction must be provided with knowledge and mental skills. Suitable education to this end is therefore necessary and is divided into two parts; Technical Education and Practical Education. Project management is one aspect of Technical Education. For that matter, discuss the relevance of project management and narrow down to four importance of it as a profession.

In comparing probability distributions, which of the following statements is TRUE?

Select one:

2. The exponential and Poisson distributions are interchangeable because they have the exact same
random variable.

3. The geometric and negative binomial distributions both have a random number of trials.

4. The uniform and normal distributions have the same distribution shapes.

5. The Poisson distribution is the limiting form of the negative binomial distribution.

Do you believe fuel cells will be the future of automobiles and small heat engines? Why or Why not? If not, what do you believe is the future?

Insight on:

a) Highway drainage and Slope protection Design

b) Highway Pavement Design, Materials and Construction & Equipment Utilization

Explain briefly the importance of serviceability limit state in the design stage for the structures

A quarter circle of radius 100 mm lies on Quadrant II of a coordinate plane with
reference radius at the origin. A rectangle is attached to the quarter circle at Quadrant I
with base at the x-axis of width equal to 25 mm and height same as the radius of the
quarter circle. Another rectangle with inverse dimension as the previous is attached to the
quarter circle at Quadrant III.
a. What is the moment of inertia (m4) of the composite area with respect to the x-axis at point O?
b. What is the moment of inertia (m4) of the composite area with respect to the y-axis at point O?
c. What is the polar moment of inertia (m4) of the composite area?
d. What is the centroidal moment of inertia (m4) of the composite area?
e. What is the radius of gyration (mm) of the composite area with respect to its
centroid?

WRITE A VACATION WORK REPORT FOR CIVIL ENGINEERING STUDENT

Choose an environmentally unsustainable industrial practice. Briefly define and explain your chosen unsustainable industrial practice. Then, use three green engineering principles to mitigate the effects of this practice on the environment. For each green engineering principle, you should articulate how each principle can mitigate the environmental effects of the chosen unsustainable practice.

Principles:

1. Designers need to strive to ensure that all material and energy inputs and outputs are as inherently non-hazardous as possible

2. It is better to prevent waste than to treat or clean up waste after it is formed

3. Separation and purification operations should be a component of the design framework

4. System components should be designed to maximise mass, energy and temporal efficiency

5. System components should be output pulled rather than input pushed through the use of energy and materials

6. Embedded entropy and complexity must be viewed as an investment when making design choices on recycle, reuse or beneficial disposition

7. Targeted durability, not immortality, should be a design goal

8. Design for unnecessary capacity or capability should be considered a design flaw. Including ‘one fits all’ solutions

9. Multi-component products should strive for material unification to promote disassemble and value retention (minimise material diversity)

10. Design of processes and systems must include integration and interconnectivity with available energy and material flows

11. Performance metrics include designing for performance in commercial ‘after-life’

12. Design should be based on renewable and readily available inputs

a) In order to meet the industrial and environmental demands and challenges posed by the rapidly developing technological advancement, and promotion of sanity in the country, and in the world at large, it is necessary to create and develop the awareness and interest of Civil Engineering students who are to become the future middle level manpower in the Construction Industry. According to Harris et al (2006:13), quality control is “a set of activities or techniques undertaken to ensure that all quality requirements are being met”. In order to achieve this purpose, processes are monitored. Coin a comprehensive definition of quality control to this effect.

b) Civil Engineering students are introduced to the principles and importance of quality control. Effectiveness of quality control in any given company cannot be quantified by customers. The variability of quality control results often lead to the loss of competitive edge. If this is limitation, then explain.

c) Administration and site work during a contract can be divided into many important areas which require some degree of control, the ultimate responsibility for which lies with the site manager. Examine the various aspects in a building project where quality could be determined.. AN,