Question

In: Mechanical Engineering

A U- tube manometer is used to measure the pressure of oil of specific gravity 0.85...

A U- tube manometer is used to measure the pressure of oil of specific gravity 0.85 flowing in a pipe line. It is left end is connected to the pipe and right –limb id open to the atmosphere. The center of the pipe is 100 mm below the level of mercury (specific gravity =13.6) the right limb .if the difference of mercury level in the two limbs is 160 mm. determine the absolute pressure of the oil in the pipe.

Solutions

Expert Solution

Hydrostatic law is used to find absolute pressure in the oil pipe.


Related Solutions

A U-tube manometer employs a special oil having a specific gravity of 0.2 for the manometer...
A U-tube manometer employs a special oil having a specific gravity of 0.2 for the manometer fluid. One side of the manometer is open to local atmospheric pressure of 24.3 inHg and the difference in column heights is measured as 10 cm±1.0 mm when exposed to an air source at 35◦C. Standard acceleration of gravity is present. Calculate the pressure of the air source in pascals and its uncertainty. 1. (a)Plot the Voltage vs. Displacement graph of LVDT Transducer by...
Construct a vertical U-tube manometer to measure the pressure difference across a flow section. Explain in...
Construct a vertical U-tube manometer to measure the pressure difference across a flow section. Explain in details and write an equation relating to the pressure difference to the difference in liquid level. Recommend TWO techniques to increase the sensitivity of a manometer. Justify your recommendation with the aid of diagrams and equations.
Does a manometer (with one side open) measure absolute pressure or gauge pressure?
Does a manometer (with one side open) measure absolute pressure or gauge pressure? How about a barometer? A tire pressure gauge? A sphygmomanometer?
A tube is placed vertically in a beaker of salt water with a specific gravity of...
A tube is placed vertically in a beaker of salt water with a specific gravity of 1.15. The interfacial tension between the air and the water is 32 mN/m and the contact angle is 30 degrees, calculate: a) Capillary pressure in psi if the tube diameter is 0.0001 cm. b) Capillary rise of water in tube. c) If the cap rock thickness is 2ft, do you think this will stop water migration? d) Radius in inches of the largest pore,...
A “U” shaped tube (with a constant radius) is filled with water and oil as shown....
A “U” shaped tube (with a constant radius) is filled with water and oil as shown. The water is a height h1 = 0.36 m above the bottom of the tube on the left side of the tube and a height h2 = 0.1 m above the bottom of the tube on the right side of the tube. The oil is a height h3 = 0.33 m above the water. Around the tube the atmospheric pressure is PA = 101300...
1. Oil with a specific gravity of 0.75 is pumped by a centrifugal pump at 375...
1. Oil with a specific gravity of 0.75 is pumped by a centrifugal pump at 375 gpm, 19 hp, and 81% efficiency. Determine the pressure head in terms of: a) Feet of oil b) Feet of water answers: a) 217 ft b) 162 ft
liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell...
liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell passes and four tube passes. water is heated in the shell side from 10°C to 50°C while the oil is cooled from 90°C to 60°C. the overall heat transfer coefficient is 53 W/m^2*K. the specific heat of the oil is 2.0 kJ/kg*K. Using the NTU - effectiveness method, calculate the area of the heat exchanger for a total energy transfer of 500 kW. what...
Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter...
Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter of 100 mm and 50 mm at the sections 1 and 2 respectively. The velocity of crude oil at the section 1 is 550 cm/s. The   section 1 is 3000 mm and section 2 is 2000 mm above the datum. If the pressure at the section 1 is 0.2 N/mm2, find the intensity of pressure at section 2?
(Fluid):- Density, Specific weight, Specific gravity, Salinity, Compressibility, Vapor pressure, and Surface tension: Explain how these...
(Fluid):- Density, Specific weight, Specific gravity, Salinity, Compressibility, Vapor pressure, and Surface tension: Explain how these properties might explain the behavior of a fluid, or explain something you observe every day please give one brief sentence for each.
A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large...
A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large industrial gas turbine engine. The flow rate of cooling water through the inner tube (Di = 25 mm) is 0.2 kg/s, while the flow rate of oil through the outer annulus (Do = 45 mm) is 0.1 kg/s. The oil and water enter at temperatures of 100 and 30 C, respectively. How long must the tube be made if the outlet temperature of the...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT