Construct a vertical U-tube manometer to measure the pressure difference across a flow section. Explain in...

Construct a vertical U-tube manometer to measure the pressure difference across a flow section. Explain in details and write an equation relating to the pressure difference to the difference in liquid level. Recommend TWO techniques to increase the sensitivity of a manometer. Justify your recommendation with the aid of diagrams and equations.

Solutions

Expert Solution

samet mamat answered 7 months ago

Next > < Previous

Related Solutions

A U-tube manometer employs a special oil having a specific gravity of 0.2 for the manometer...

A U-tube manometer employs a special oil having a specific gravity of 0.2 for the manometer fluid. One side of the manometer is open to local atmospheric pressure of 24.3 inHg and the difference in column heights is measured as 10 cm±1.0 mm when exposed to an air source at 35◦C. Standard acceleration of gravity is present. Calculate the pressure of the air source in pascals and its uncertainty. 1. (a)Plot the Voltage vs. Displacement graph of LVDT Transducer by...

Does a manometer (with one side open) measure absolute pressure or gauge pressure?

Does a manometer (with one side open) measure absolute pressure or gauge pressure? How about a barometer? A tire pressure gauge? A sphygmomanometer?

What is the difference between U-tube differential manometers and inverted U-tube differential manometers?

Explain how flow through a blood vessel is determined. Explain what a “pressure difference” is and...

Explain how flow through a blood vessel is determined. Explain what a “pressure difference” is and why it matters to flow. Define resistance and explain how resistance affects flow. List and discuss the 3 factors which influence the resistance through vessels. For each factor explain the mechanism by which it affects resistance. Which one of these 3 as the largest impact on resistance? Explain why it has the largest impact on flow. Which one of these 3 can readily be...

Explain how to flow through a blood vessel is determined. Explain what a “pressure difference” is...

Explain how to flow through a blood vessel is determined. Explain what a “pressure difference” is and why it matters to flow. Define resistance and explain how resistance affects flow. List and discuss the 3 factors which influence the resistance through vessels. For each factor explain the mechanism by which it affects the resistance. Which one of these 3 as the largest impact on resistance? Explain why it has the largest impact on flow. Which one of these 3 can...

Atmospheric air enters the heated section of a circular tube at a flow rate of .005...

Atmospheric air enters the heated section of a circular tube at a flow rate of .005 kg/s and a temperature of 20 degrees Celsius. The tube is of diameter D = 50 mm, and fully developed conditions with h = 25 W/m^2K exist over the entire length of L = 3m. a) For the case of the uniform surface heat flux at q''s = 1000 W/m2 , determine the total heat transfer rate q and the mean temperature of the...

An orifice meter is used to measure flow rate of liquid in pipe shows a pressure...

An orifice meter is used to measure flow rate of liquid in pipe shows a pressure difference of ' x ' m of water column when the flow rate is Q If flow rate is doubled then what is delta P?

Michael Faraday unsuccessfully attempted to measure the potential difference across the River Thames due to the...

Michael Faraday unsuccessfully attempted to measure the potential difference across the River Thames due to the flow of water (which is a good conductor due to dissolved salts) in the earth's field. At Waterloo Bridge, where Faraday made his attempt, the river is 200 m wide and flows eastward at 2.4m/s . The earth's magnetic field here has a magnitude of 50 ?T and is tipped 65?from the horizontal, so it has both horizontal (north) and vertical (down) components. Part...

explain the design , construction and working of a parallel and counter flow shell and tube...

explain the design , construction and working of a parallel and counter flow shell and tube types of heat echangers? also draw figures

Explain the difference between finding the horizontal and vertical asymptotes. When will there be a point...

Explain the difference between finding the horizontal and vertical asymptotes. When will there be a point of discontinuity? What could the graph look like when there is no horizontal or vertical asymptotes.

Subjects