Question

In: Electrical Engineering

Electromagnetic Waves: Design single stub matching network for the transmission line of Zo = 50 ohms...


Electromagnetic Waves:
Design single stub matching network for the transmission line of Zo = 50 ohms terminated with Z1 = 100+ j100 ohms. Find SWR and Reflection Coefficient .

Solutions

Expert Solution

Kindly upvote if its helpful to you


Related Solutions

A 100 ohms load is connected to a 50 ohms transmission line. Determine the value of...
A 100 ohms load is connected to a 50 ohms transmission line. Determine the value of the reactance to put in series at the input to the line and the length in wavelengths of the shortest transmission line to match with a 50 ohms source.
a single stub tuner, connected in parallel, has a 50 ohm main line, and a 50...
a single stub tuner, connected in parallel, has a 50 ohm main line, and a 50 ohm short- circuited stub .It is used to match a load of Zr = 20+j70 to a 50 ohm system. What are the lengths of the line and stub in centimeters if the single stub tuner is using air filled coaxial lines and the system is operating at 600MHz
Assume a transmission line with ZL = 65 + j40Ω and Zo = 30Ω. If the...
Assume a transmission line with ZL = 65 + j40Ω and Zo = 30Ω. If the frequency of the line is 2GHz, use the Smith Chart to find: i) the reflection coefficient; ii) the distance to the first voltage maximum; iii) the voltage standing wave ratio; iv) the admittance of the load; v) the position of the short-circuited stub on the main line for a perfect impedance matching; vi) the length of the short-circuited stub. (Show all steps on the...
Assume a transmission line with ZL = 65 + j40 Ω and Zo = 30 Ω....
Assume a transmission line with ZL = 65 + j40 Ω and Zo = 30 Ω. If the frequency of the line is 2GHz, use the Smith Chart to find: i) the reflection coefficient; ii) the distance to the first voltage maximum; iii) the voltage standing wave ratio; iv) the admittance of the load; v) the position of the short-circuited stub on the main line for a perfect impedance matching; vi) the length of the short-circuited stub. (Show all steps...
Assume a transmission line with ZL = 65 + j40 Ω and Zo = 60 Ω....
Assume a transmission line with ZL = 65 + j40 Ω and Zo = 60 Ω. If the frequency of the line is 2GHz, use the Smith Chart to find: i) the reflection coefficient; ii) the distance to the first voltage maximum; iii) the voltage standing wave ratio; iv) the admittance of the load; v) the position of the short-circuited stub on the main line for a perfect impedance matching; vi) the length of the short-circuited stub. (Show all steps...
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 −...
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 − j47.5) Ω using a short circuited stub. Use the Smith chart to determine position and length line for the stub? show step by step by hand and draw by hand I want details so I can understand
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 −...
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 − j47.5) Ω using a short circuited stub. Use the Smith chart to determine position and length line for the stub? show step by step I want details so I can understand
Assume a transmission line with ZL = 100 − j25 Ω and Z0 = 50 Ω....
Assume a transmission line with ZL = 100 − j25 Ω and Z0 = 50 Ω. Using the smith chart, find i) the normalised load impedance; ii) the corresponding reflection coefficient; iii) the standing wave ratio; iv) the distance between the load and the first voltage maximum; v) the distance between the load and the first voltage minimum; vi) the normalised admittance; vii) the input impedance at 0.2λ from the load. (Show all steps on the Smith chart)
I'm working on a project where I need to design a transmission line tap for a...
I'm working on a project where I need to design a transmission line tap for a station generator. The parameters include sizing three switches for the tap where at least one is a loop break switch. From where to start? What kind of calculations are needed to size the switches? What are those switches?
8. A 100 W load is connected to a 50 W transmission line. Determine the value...
8. A 100 W load is connected to a 50 W transmission line. Determine the value of the reactance to put in series at the input to the line and the length in wavelengths of the shortest transmision line to match with a 50 W source.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT