Assume a transmission line with ZL = 100 − j25 Ω and Z0 = 50 Ω....

Assume a transmission line with ZL = 100 − j25 Ω and Z0 = 50 Ω. Using the smith chart, find i) the normalised load impedance; ii) the corresponding reflection coefficient; iii) the standing wave ratio; iv) the distance between the load and the first voltage maximum; v) the distance between the load and the first voltage minimum; vi) the normalised admittance;

vii) the input impedance at 0.2λ from the load. (Show all steps on the Smith chart)

Solutions

Expert Solution

Manojponduru answered 1 week ago

Next > < Previous

Related Solutions

Assume a transmission line with ZL = 100 − j25Ω and Z0 = 50Ω. Using the...

Assume a transmission line with ZL = 100 − j25Ω and Z0 = 50Ω. Using the smith chart, ﬁnd i) the normalised load impedance; ii) the corresponding reﬂection coeﬃcient; iii) the standing wave ratio; iv) the distance between the load and the ﬁrst voltage maximum; v) the distance between the load and the ﬁrst voltage minimum; vi) the normalised admittance; vii) the input impedance at 0.2λ from the load. (Show all steps on the Smith chart)

Assume a transmission line with ZL = 65 + j40 Ω and Zo = 60 Ω....

Assume a transmission line with ZL = 65 + j40 Ω and Zo = 60 Ω. If the frequency of the line is 2GHz, use the Smith Chart to find: i) the reflection coefficient; ii) the distance to the first voltage maximum; iii) the voltage standing wave ratio; iv) the admittance of the load; v) the position of the short-circuited stub on the main line for a perfect impedance matching; vi) the length of the short-circuited stub. (Show all steps...

Assume a transmission line with ZL = 65 + j40 Ω and Zo = 30 Ω....

Assume a transmission line with ZL = 65 + j40 Ω and Zo = 30 Ω. If the frequency of the line is 2GHz, use the Smith Chart to find: i) the reflection coefficient; ii) the distance to the first voltage maximum; iii) the voltage standing wave ratio; iv) the admittance of the load; v) the position of the short-circuited stub on the main line for a perfect impedance matching; vi) the length of the short-circuited stub. (Show all steps...

Derive the input impedance of the transmission line of Z0, length ‘l’ and terminated with Zl.

Assume a transmission line with ZL = 65 + j40Ω and Zo = 30Ω. If the...

Assume a transmission line with ZL = 65 + j40Ω and Zo = 30Ω. If the frequency of the line is 2GHz, use the Smith Chart to ﬁnd: i) the reﬂection coeﬃcient; ii) the distance to the ﬁrst voltage maximum; iii) the voltage standing wave ratio; iv) the admittance of the load; v) the position of the short-circuited stub on the main line for a perfect impedance matching; vi) the length of the short-circuited stub. (Show all steps on the...

A 50 ohm transmission line has an unknown load impedance ZL. A voltage maximum occurs at...

A 50 ohm transmission line has an unknown load impedance ZL. A voltage maximum occurs at z = -0.15(wavelength). At z = -0.20(wavelength) the real part of the impedance is 30 ohms. Find ZL using the Smith chart.

A lossless 50-Ω transmission line is terminated in a load with Z L = (35 −...

A lossless 50-Ω transmission line is terminated in a load with Z L = (35 − j47.5) Ω using a short circuited stub. Use the Smith chart to determine position and length line for the stub? show step by step by hand and draw by hand I want details so I can understand

A lossless 50-Ω transmission line is terminated in a load with Z L = (35 −...

345 kV, 50 Hz, 3-phase transmission line is 100 km long. The resistance is 0.048 Ω/km...

345 kV, 50 Hz, 3-phase transmission line is 100 km long. The resistance is 0.048 Ω/km and the inductance is 1,24 mH/km. The shunt capacitance is 0.0174 μF/km. The receiving end load is 216 MW with 0.8 power factor lagging at 325 kV. (a) Compute ABCD parameters using π equivalent circuit (b) Sending end voltage VS, (c) Sending end current IS, (d) Efficiency

Assuming that the length of a lossless transmission line with the normalized load impedance of zL...

Assuming that the length of a lossless transmission line with the normalized load impedance of zL = ZL/Z0 = 1 + j1 is l = 2.25λz , there are a total of (A) 2 voltage maxima and 2 voltage minima (B) 2 voltage maxima and 3 voltage minima (C) 3 voltage maxima and 2 voltage minima (D) 4 voltage maxima and 4 voltage minima (E) 4 voltage maxima and 5 voltage minima (F) 5 voltage maxima and 4 voltage minima...

Subjects