Question

In: Electrical Engineering

A 100 ohms load is connected to a 50 ohms transmission line. Determine the value of...

A 100 ohms load is connected to a 50 ohms transmission line. Determine the value of the reactance to put in series at the input to the line and the length in wavelengths of the shortest transmission line to match with a 50 ohms source.

Solutions

Expert Solution

Manojponduru answered 1 year ago
Next > < Previous

Related Solutions

8. A 100 W load is connected to a 50 W transmission line. Determine the value...
8. A 100 W load is connected to a 50 W transmission line. Determine the value of the reactance to put in series at the input to the line and the length in wavelengths of the shortest transmision line to match with a 50 W source.
A) A 150 + j300 Ohm load is connected to a 75 Ohm transmission line. Determine...
A) A 150 + j300 Ohm load is connected to a 75 Ohm transmission line. Determine the value of the reactance to put in parallel at the input to the line and the length in wavelengths of the shortest transmission line to match with a 75 Ohm source. B) Redo A using a short-circuited stub as the equivalent parallel reactance.
9. A 150 + j300 W load is connected to a 75 W transmission line. Determine...
9. A 150 + j300 W load is connected to a 75 W transmission line. Determine the value of the reactance to put in parallel at the input to the line and the length in wavelengths of the shortest transmission line to match with a 75 W source. Redo problem 9 using a short-circuited stub as the equivalent parallel reactance.
An unbalanced wye connected wye connected load of three phase resistances with Ra=60 ohms, Rb=40 ohms...
An unbalanced wye connected wye connected load of three phase resistances with Ra=60 ohms, Rb=40 ohms and Rc=80 ohms is connected to a 440V, negative sequence, balanced 3 phase, 3 wire supply. Calculate the complex power using the method of symmetrical components. Please show all steps and clearly show all answers.
Electromagnetic Waves: Design single stub matching network for the transmission line of Zo = 50 ohms...
Electromagnetic Waves: Design single stub matching network for the transmission line of Zo = 50 ohms terminated with Z1 = 100+ j100 ohms. Find SWR and Reflection Coefficient .
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 −...
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 − j47.5) Ω using a short circuited stub. Use the Smith chart to determine position and length line for the stub? show step by step by hand and draw by hand I want details so I can understand
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 −...
A lossless 50-Ω transmission line is terminated in a load with Z L = (35 − j47.5) Ω using a short circuited stub. Use the Smith chart to determine position and length line for the stub? show step by step I want details so I can understand
A 3.5 current source is connected to a 220 ohms load. The source resistance is 6kohms....
A 3.5 current source is connected to a 220 ohms load. The source resistance is 6kohms. Solve for the equivalent voltage source (E and Rs) for this practical source.
A 50 ohm transmission line has an unknown load impedance ZL. A voltage maximum occurs at...
A 50 ohm transmission line has an unknown load impedance ZL. A voltage maximum occurs at z = -0.15(wavelength). At z = -0.20(wavelength) the real part of the impedance is 30 ohms. Find ZL using the Smith chart.
Assume a transmission line with ZL = 100 − j25 Ω and Z0 = 50 Ω....
Assume a transmission line with ZL = 100 − j25 Ω and Z0 = 50 Ω. Using the smith chart, find i) the normalised load impedance; ii) the corresponding reflection coefficient; iii) the standing wave ratio; iv) the distance between the load and the first voltage maximum; v) the distance between the load and the first voltage minimum; vi) the normalised admittance; vii) the input impedance at 0.2λ from the load. (Show all steps on the Smith chart)
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT