Question

In: Electrical Engineering

An 8-bit A/D Converter on a chip using 0.18um technology with a Vdd=1.8V is built using...

An 8-bit A/D Converter on a chip using 0.18um technology with a Vdd=1.8V is built using minimum size transistors (l=0.18um and w=0.36um). It has 22 transistors per bit in conversion and 128 transistors used for memory. The activity factor in the conversion modules is 0.1, while the activity factor in the memory blocks is 0.02. Assume each transistor contributes 3fF/um of gate capacitance and 0.24fF/um of diffusion capacitance. Estimate the switching power without capacitance when operating at 1MHz.

Solutions

Expert Solution


Related Solutions

Suppose you have an 8-bit A/D converter that has a full-scale input range of ︎2V to...
Suppose you have an 8-bit A/D converter that has a full-scale input range of ︎2V to ︎6V. When a particular voltage is applied, the computer records the hex number B3. Assuming a perfect calibration, answer the following questions: - What output voltage does this value correspond to? - What is the digitization (quantization) error in the voltage? - By how much percent would this error change if 12 bits were used to approximate the output instead of 8 bits? PLEASE...
Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in...
Design and build an 8 bit Digital to Analog Converter using the LM741 OP Amp in Multisim software. Analyze the system using 1000 1000, 1111 1110, and other four different byte values.
Analog-to-Digital convertor, modified. Assume that you have a 12-bit A/D converter that can digitize an analog...
Analog-to-Digital convertor, modified. Assume that you have a 12-bit A/D converter that can digitize an analog voltage over the range of 0.00 Volts to + 3.30 Volts (just like the one in the TM4C123G). (a) What is the minimum voltage that an analog input voltage could change and be guaranteed to be detected by a change in the digital output value? E.g. in millivolts or microvolts. (b) What is the binary number that represents an analog voltage of +1.11 volts?...
1. Design and implement a 4 bit binary to excess 3 code converter using CMOS transistors....
1. Design and implement a 4 bit binary to excess 3 code converter using CMOS transistors. (Note: Students are expected to design the circuit with truth table, solve the output expression by use of K Map or suitable circuit Reduction technique and implement using CMOS transistors.)
Design and Test an 8-bit Adder using 4-bit adder. Use 4-bit adder coded in class using...
Design and Test an 8-bit Adder using 4-bit adder. Use 4-bit adder coded in class using full adder that is coded using data flow model. Use test bench to test 8-bit adder and consider at least five different test vectors to test it.
Design and Test an 8-bit Adder using 4-bit adder. Use 4-bit adder coded in class using...
Design and Test an 8-bit Adder using 4-bit adder. Use 4-bit adder coded in class using full adder that is coded using data flow model. Use test bench to test 8-bit adder and consider at least five different test vectors to test it. in behavioral not endmodule plz help me
Define the following terms related to D/A converter;                                 &nbsp
Define the following terms related to D/A converter;                                               (i) resolution   (ii) accuracy    (iii) settling time         (iv) offset error      (v) gain error
Represent -60 in binary using 8-bit signed magnitude. Add the following unsigned 8 bit binary numbers...
Represent -60 in binary using 8-bit signed magnitude. Add the following unsigned 8 bit binary numbers as shown. 01110101 + 00111011 Add the following unsigned 8 bit binary numbers as shown. 01000100 + 10111011
Write an instruction sequence to configure the A/D converter of the PIC18F452 to operate with the...
Write an instruction sequence to configure the A/D converter of the PIC18F452 to operate with the following parameters: Conversion result right justified fosc=32 MHz Highest ambient temperature may reach 600oC Use VDD and VSS as the high and low reference voltages Convert channel AN0 Enable A/D Module
please i need the code for an 8 bit by 8 bit multiplier in verilog ....
please i need the code for an 8 bit by 8 bit multiplier in verilog . ( pls the code should be clearly written and BOLD)
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT