Q1: Design L2L3 member as shown below using double-angle section with 3/8-in gusset plate between the...

Q1: Design L2L3 member as shown below using double-angle section with 3/8-in gusset plate between the angles. Assume two-lines of three ¾-in bolts in each vertical angle-leg, spaced at 4-in on center. Use A36 steel.

Q2: Draw (sketch) the connections at L2 and L3 assuming all truss members are designed using double angle sections, and using the same amount of bolts.

PD= 60 kips, PL=48 kips

Expert Solution

Ally Wells answered 6 months ago

Select double angle tension member to resist a factored load of 100 kips. Member is connected...

Select double angle tension member to resist a factored load of 100 kips. Member is connected with 2 lines of 3⁄4-inch diameter bolts placed at usual gage distances (see AISC manual specification J3.3). There will be more than 2 bolts in each line. Member is 15’-0” long. Hint: Try an angle with 6 inch legs back to back and an outstanding length of 3 1⁄2 -inches. Choose required thickness. Assume U=0.85 for design.

Design a welded compression member composed of double standard channels, placed face to face, using A36...

Design a welded compression member composed of double standard channels, placed face to face, using A36 steel. Length of the member is 7.5m and the maximum compressive factor force is 3R KN. Distance between centroid of the channels is to be 300mm. Design the section, end plates and the lacing system K=1.0 TAKE R =2071

Find the measure of angle A in the figure shown below

Given the matrix as shown below n_array = 3 1 8 3 5 7 4 9...

Given the matrix as shown below n_array = 3 1 8 3 5 7 4 9 2 Write a M-file script program that generates this n_array, and answer each question using one line of MATLAB statement. a) Replace the second column of the n_array with a column of 0s b) Replace the element in the second-row, third-column with a zero c) Change the n_array to a 4 x 3 array by adding a row of 0s The end result for...

2. Design an all-bolted double-angle connection for a W24x146 A992 beam to carry a dead load...

2. Design an all-bolted double-angle connection for a W24x146 A992 beam to carry a dead load reaction of 25 kips and a live load reaction of 75 kips. Use 5/16 in. angles and ¾ in A325N bolts in standard holes. The uncoped beam is connected to the flange of a W14x132 column. Design by both LRFD and ASD method.

If you were a member of the NLRB, would you rule that HCR violated section 8(a)(1)...

If you were a member of the NLRB, would you rule that HCR violated section 8(a)(1) of the NLRB by discharging the three nurses (assuming that they were covered by the NLRA)? Why or why not?

Compute the future worth of alternative P shown below, using an interest rate of 8% per...

Compute the future worth of alternative P shown below, using an interest rate of 8% per year using LCM method P Q First cost, $ -23,000 -30,000 Annual operating cost, $ per year -4,000 -2,500 Salvage value, $ 3,000 1,000 Life, years 3 6

Design the lightest W16 tension member section of steel of Fy= 50 ksi, Fu= 65 ksi...

Design the lightest W16 tension member section of steel of Fy= 50 ksi, Fu= 65 ksi to support a tensile service dead load PD = 270 k and a tensile service load PL= 220 k. the member is to be 53 ft. long the member is to have two lines of bolts in each flange for 7/8-in bolts (there are three in a line 4 in on center). At the end you should make the necessary checks. ACI Code

A steel cantilever member as shown below is subjected to a transverse load at its end...

A steel cantilever member as shown below is subjected to a transverse load at its end that varies from 135 N to -45 N as axial load varies from 450 N to -110 N. Determine the required diameter at the change of section for infinite life using a factor of safety of 2. The strength properties of the material are: Sut=550 MPa, Sy=470 MPa, Se(corrected)=275 MPa, Test data indicate that the theoretical stress concentration factor for bending and axial loads...

Sequence the jobs shown below by using a Gantt chart. Assume that the move time between...

Sequence the jobs shown below by using a Gantt chart. Assume that the move time between machines is one hour. Sequence the jobs in priority order 1, 2, 3, 4. Job Work Center/Machine Hours Due Date (days) 1 A/3, B/2, C/2 3 2 C/2, A/4 2 3 B/6, A/1, C/3 4 4 C/4, A/1, B/2 3 Which department is the bottleneck? Calculate the machine utilization?

Question