Question

In: Civil Engineering

Design a welded compression member composed of double standard channels, placed face to face, using A36...

Design a welded compression member composed of double standard channels, placed face to face, using A36 steel. Length of the member is 7.5m and the maximum compressive factor force is 3R KN. Distance between centroid of the channels is to be 300mm. Design the section, end plates and the lacing system K=1.0

TAKE R =2071

Solutions

Expert Solution

ANSWER:--

COMPRESSIVE FACTOR FORCE:-- The compressibility factor (Z), also known as the compression factor or the gas deviation factor, is a correction factor which describes the deviation of a real gas from ideal gas behaviour. It is simply defined as the ratio of the molar volume of a gas to the molar volume of an ideal gas at the same temperature and pressure.

CENTROID:-- the center of mass of a geometric object of uniform density

Ally Wells answered 1 year ago
Next > < Previous

Related Solutions

A welded tension member is to consist of two channels placed 400mm back to back with...
A welded tension member is to consist of two channels placed 400mm back to back with the flanges turned out. Select the channels for a factored tensile load of 4R KN using A36 steel and the AISC specification. The member is to be 30m long. TAKE R =2071
Q1: Design L2L3 member as shown below using double-angle section with 3/8-in gusset plate between the...
Q1: Design L2L3 member as shown below using double-angle section with 3/8-in gusset plate between the angles. Assume two-lines of three ¾-in bolts in each vertical angle-leg, spaced at 4-in on center. Use A36 steel. ​ Q2: Draw (sketch) the connections at L2 and L3 assuming all truss members are designed using double angle sections, and using the same amount of bolts. PD= 60 kips, PL=48 kips​    
Design a four stroke cycle for SI engine using crankcase compression. Draw schematics of the six...
Design a four stroke cycle for SI engine using crankcase compression. Draw schematics of the six basic process: intake, compression, combustion, expansion, blowdown and exhaust. Describe fully the intake of air, fuel and oil.
Two identical double-pipe heat exchangers are constructed of a 2-in standard schedule 40 pipe placed inside...
Two identical double-pipe heat exchangers are constructed of a 2-in standard schedule 40 pipe placed inside a 3-in standard pipe. The length of the exchangers is 10 ft; 40 gal/min of water initially at 80◦F is to be heated by passing through the inner pipes of the exchangers in a series arrangement, and 30 gal/min of water at 120◦F and 30 gal/min of water at 200◦F are available to accomplish the heating. The two heating streams may be mixed in...
Design an ECG amplifier using 3 operational amplifiers for standard (AHA) specifications.
Design an ECG amplifier using 3 operational amplifiers for standard (AHA) specifications.
Design a fluidized bed gasifier with a required syngas output of 2.5 m3/min (standard conditions) using...
Design a fluidized bed gasifier with a required syngas output of 2.5 m3/min (standard conditions) using a cylindrical cross section. The air-to-fuel ratio should be 70% of the stoichiometric requirements and sawdust will be used as fuel. The ultimate analysis is as follows: C=49.7%; H=6.2%; O=42.53%, N=0.7%; S=0.17%, and ash =0.7%. The superficial velocity should be 0.03 m/s and the air density at standard conditions is equal to 1.2 kg/m3. About 25 kg of biomass is used every hour. [MW:...
Using 7/8 in diameter ASTM A325-N bolts in standard holes and E70 electrodes. Design a bolted...
Using 7/8 in diameter ASTM A325-N bolts in standard holes and E70 electrodes. Design a bolted flange-plated FR moment connection between a W12×50 beam and a W14×90 column flange (RD = 15 kips; MD = 60 kip-ft) and (RL = 30 kips; ML = 120 kip-ft). For shear plate use three bolts:(i)Check the beam available flexural strength (ii)Design single-plate web connection (iii)Check the connecting elements rupture strength at welds Sketch the connection.
Using 7/8 in diameter ASTM A325-N bolts in standard holes and E70 electrodes. Design a bolted...
Using 7/8 in diameter ASTM A325-N bolts in standard holes and E70 electrodes. Design a bolted flange-plated FR moment connection between a W12×50 beam and a W14×90 column flange (RD = 15 kips; MD = 60 kip-ft) and (RL = 30 kips; ML = 120 kip-ft). For shear plate use three bolts: (I) Check the beam available flexural strength (ii) Design single-plate web connection (iii) Check the connecting elements rupture strength at welds Sketch the connection.
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT