Use diagram to explain the layout of domestic (cold) water system from the underground main pipe...

Use diagram to explain the layout of domestic (cold) water system from the underground main pipe to the inspection chamber (manhole). Label all piping and fittings.

Solutions

Expert Solution

While supplying the water from the main pipe to the inspection chamber or manhole, the water is being distributed or provided of two types that is the cold water and hot water. Here we are going to discuss about the layout of the domestic cold water system. The water is supplied to the main Valve from the Main pipe lines. The water is distributed to two different sections from the valves given above. One leads to the air ventilation above and other towards the heat exchanger. As we are going to discuss about cold water only then the water is supplied to the line with air ventilation. Cold natural air is being passed and due to that the temperature of the pipeline is relatively low and that helps in chilling of water. Then the water is being supplied to the sub arteries to the domestic places in form of cold water and the other line where water is distributed is used for providing the hot water. Please refer the diagram for more clear view of the layout for the cold water supply for domestic purpose.

Ally Wells answered 1 month ago

Next > < Previous

Related Solutions

types of plastic pipe that can be used for hot and cold water distribution: 1. 2....

types of plastic pipe that can be used for hot and cold water distribution: 1. 2. 3. List 3 types of plastic pipe used for sanitary drainage and vent piping: 1. 2. Black iron steel pipe is used for carrying ____________________ or ____________________. The cast iron pipes no-hub pipes are used for below ground or above ground?_________________ Type _____ copper pipe is the most commonly used in residential water lines. What color is the copper pipe, most commonly used in...

Cold water inside / outside diameter in the same axis two pipe heat exchanger used as...

Cold water inside / outside diameter in the same axis two pipe heat exchanger used as engine oil cooler It enters the 25/30 mm steel pipe at a temperature of 15 degrees at a speed of 0.5 m / s, Take off at a temperature of 25 degrees.Hot oil, on the inside / outside diameter of 40/46 mm steel pipe, at a temperature of 60 degrees with a speed of 0.25 m / s. enters.it is desired to cool the...

Use demand and supply diagram to explain what will happen to domestic tourism industry in Auckland...

Use demand and supply diagram to explain what will happen to domestic tourism industry in Auckland (only consider tourism demand from people within the country): a) a rise in unemployment in New Zealand. b) there is an increase in the government allowance to jobless in New Zealand.

Question 1) As water passes from a pipe of larger diameter to a pipe of smaller...

Question 1) As water passes from a pipe of larger diameter to a pipe of smaller diameter in converging section, the static pressure: Becomes half Increases Decreases Does not change Question 2) The following reading have to be recorded from the flow measurement apparatus to calculate the mass flow rate from the venturimeter? Pressures at the inlet and exit of the venturimeter Pressures at the inlet and throat of the venturimeter The rotameter reading venturimeter The pressure at the throat...

Water travels through a pipe at 5.13 m/s. The pipe expands from a crossectional area of...

Water travels through a pipe at 5.13 m/s. The pipe expands from a crossectional area of 2.9 m2 to an area of 11.6 m2. What is the speed of the water in the second part of the pipe in m/s? How much is the pressure change in KPa as the pipe expands? The density of water is 1000 kg/m3. Enter a positive value for an increase in pressure, a negative value for a decrease. (Kpa)

(a) Use the phase diagram for water and a few well-written prose sentences to explain why,...

(a) Use the phase diagram for water and a few well-written prose sentences to explain why, at sea level, large vapor bubbles do not form in a pot of water at 95 oC. (Actually, small bubbles can appear at this temperature. This is simmering, not boiling.) (b) By integrating the Clausius-Clapeyron equation from (T0,P0) = (100 oC, 1.00 atm), calculate the ambient pressure in a kitchen where water does in fact, boil at 95 oC.

[1] Suppose that the system has one main component and a (cold) standby unit. The standby...

[1] Suppose that the system has one main component and a (cold) standby unit. The standby unit will take over the main component upon its failure. If the failure rate of the components are constant with a value of 0.1/day and if the system fails if and only if both components have failed, answer the following questions. a)Set up the system using continuous-time Markov chain and obtain its generator by clearly identifying and labeling the states. b)Find the reliability of...

Question