Question

In: Civil Engineering

A simply supported reinforced concrete beam with uniformly distributed load of 10 kN/m has a span...

A simply supported reinforced concrete beam with uniformly distributed load of 10 kN/m has a span of 6.0 metres. The beam cross-section is 225 mm breadth by 300 mm depth. Sketch and design the beam. Make necessary and realistic assumptions where applicable

Solutions

Expert Solution

Ally Wells answered 1 month ago
Next > < Previous

Related Solutions

A 6-m span simply supported beam carries a uniformly distributed ultimate load of 70 kN/m. The...
A 6-m span simply supported beam carries a uniformly distributed ultimate load of 70 kN/m. The dimensions of the beam section are b = 300 mm, d = 700 mm. The beam is reinforced with bars of 25-mm diameter in one row. f’c = 25 MPa, and Fy = 420 MPa. Use # 10 U-shaped stirrups. Neglect the column width. The stirrup spacings (s) is equal to: a. 450 mm                    b. 350 mm c. 400 mm                    d. 500 mm                   
A simply supported beam of 10m span carries a uniformly distributed load of 50kN/m spread over...
A simply supported beam of 10m span carries a uniformly distributed load of 50kN/m spread over 5m from the left support and a 5kN concentrated load on its center . Its base is 250mm while deep is 500mm. Calculate the maximum deflection in mm. E = 2.0x10^5 N/mm2. Use the area moment method
A simply supported beam 10-m long is acted upon by a uniformly distributed dead load of...
A simply supported beam 10-m long is acted upon by a uniformly distributed dead load of 20 kN/m and a uniformly distributed live load of 48 kN/m throughout its span. Design the footings of each columns located at the supports using the following data Depth of Footing (Df)                                                   =             1.20 meters Allowable Soil Pressure (qall)                                      =             210 kPa Unit Weight of Soil (γs)                                                =             17 kN/m3 Unit Weight of Concrete (γc)                                      =             24 kN/m3 Design Compressive Strength of Concrete (f’c)     =             27.6 MPa Yield Strength of Reinforcing Steel (fy)                    =             276 MPa...
simply supported T-beam of 6 m clear span carries an ultimate load of 38 kN/m. The...
simply supported T-beam of 6 m clear span carries an ultimate load of 38 kN/m. The beam section dimensions, support particulars and tension reinforcement are shown in Figure Q1. Design the shear reinforcement for the beam. Data Given: The characteristic strength of the concrete is             25 N/mm2. The characteristic strength of steel reinforcement is         460N/mm2. The characteristic strength of shear reinforcement is         250N/mm2. Nominal maximum aggregate size (hagg) is             20...
A simply supported flanged beam subjected to a factored load of 60 kN/m (including dead load...
A simply supported flanged beam subjected to a factored load of 60 kN/m (including dead load and live load). The beam has an overall depth of 600 mm including slab thickness of 100 mm. The width of the beam is 230 mm, effective span of the beam is 6.25 m and effective cover to the tension reinforcement is 50 mm. Assume M25 grade concrete and Fe415 steel. Check whether the beam needs to be designed as singly reinforced or doubly...
Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a...
Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a service live load of 175 psf and a service dead load of 25 psf (the dead load does not include the self-weight of the slab). Use f’c = 3000 psi and Fy = 60,000 psi. Make the slab thickness to 1/2-in. increments.
A 15-m simply supported beam is subjected to a uniformly increasing load of zero, 3m from...
A 15-m simply supported beam is subjected to a uniformly increasing load of zero, 3m from the left support, to 30kN/m at the right support. A 20kN point load is also acting 1 meter from the left support. The cross section of the beam is 500mm x 800mm. Assume that tendons are applied in constant eccentricity of e = 150mm. Determine: Moment at midspan Maximum Moment Stress of the section where moment is maximum, assuming the effective Jacking Force to...
A simply supported beam 10m long carries a uniform load of 24 kN/m. Using E =...
A simply supported beam 10m long carries a uniform load of 24 kN/m. Using E = 200 GPa, I = 240x10^6 mm4 Using CBM (conjugate beam method): A. Determine the rotation (in degrees) of the beam at a point 4m from the left support. B. Determine the deflection at a point 4m from the left support.
. A simply supported reinforced concrete beam needs to be designed with the following details: Size...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size of Beam: 350 mm x 450 mm. Effective length of Beam: 8 m. Dead Load excluding self-weight of Beam: 30.5 kN/m Reinforcement: 25 mm bars and 8 mm stirrups Effective cover to compression reinforcement: 30 mm i. Design the beam and find out the number of bars required. ii. Design the beam for shear. iii. Draw the detailing of beam. Live load = 8KN/m...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size of Beam: 350 mm x 450 mm. Effective length of Beam: 8 m. Dead Load excluding self-weight of Beam: 30.5 kN/m Reinforcement: 25 mm bars and 8 mm stirrups Effective cover to compression reinforcement: 30 mm i. Design the beam and find out the number of bars required. ii. Design the beam for shear. iii. Draw the detailing of beam. Live load = 3KN/m...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT