Water flowing along a horizontal pipe has a speed of 2.31 m/s and a pressure of...

Water flowing along a horizontal pipe has a speed of 2.31 m/s and a pressure of 4.25 atm. Further along, the pipe narrows so that the cross-sectional area decreases by a factor of 6.17. What is the pressure in the narrow section?

Solutions

Expert Solution

genius_generous answered 1 month ago

Next > < Previous

Related Solutions

Water movinng in a horizontal pipe has a velocity of 9.0 m/s when the radius of...

Water movinng in a horizontal pipe has a velocity of 9.0 m/s when the radius of the pipe is 0.0025 metr. determine the velocity of the water when it enters a wider section of the pipe and the radius is 0.075 meter. Please show work Determine the density of a unkown smaple by using Archemdes Principle and water. the mass measurement of the sample in air is 200 grams, the mass measurement of the sample in water 147 grams. please...

Suppose the water at the top of Niagara Falls has a horizontal speed of 1.20 m/s...

Suppose the water at the top of Niagara Falls has a horizontal speed of 1.20 m/s just before it cascades over the edge of the falls. At what vertical distance below the edge does the velocity vector of the water point downward at a 47.3 ° angle below the horizontal?

Water is moving with a speed of 11.3 m/s through a pipe with a cross-sectional area...

Water is moving with a speed of 11.3 m/s through a pipe with a cross-sectional area of 4.5 cm2. The water gradually descends 30.0 m as the pipe's cross section increases by a factor of three. What is the speed of flow at the lower level? Tries 0/16 How much higher is the pressure at the lower level compared to the upper level?

Water flows in a horizontal pipe of d1=100 mm with a velocity wt=1m/s and pressure p1=90...

Water flows in a horizontal pipe of d1=100 mm with a velocity wt=1m/s and pressure p1=90 kPa. It enters a pipe reduction to a diameter d2=50 mm. Pressure after the pipe reduction drops to p2=80 kPa while temperature is unchanged. Find entropy generation rate in the zone of the pipe reduction. Assume that the surroundings is at Ts=20?C and pressure is ps=80kPa and the steady state is considered. What will be the exit pressure after the pipe reduction if the...

A water is flowing through a circular varying diameter pipe. The water completely fills the pipe...

A water is flowing through a circular varying diameter pipe. The water completely fills the pipe at all its sections. 1- What is the water velocity of the water at the first section if you know that the diameter of the pipe at this section= 22 cm and the water is flowing at a rate of 2.5 m3/s? 2- What is the diameter of the pipe at the second section if you know that the water velocity at this section...

A baseball is hit with a horizontal speed of 16 m/s and avertical speed of...

A baseball is hit with a horizontal speed of 16 m/s and a vertical speed of 12 m/s upward. What are these speeds 4 s later?horizontal speedm/svertical speedm/s

Fluid X is flowing in a circular pipe with a constant velocity ν (m/s). The fluid...

Fluid X is flowing in a circular pipe with a constant velocity ν (m/s). The fluid is cooled by a jacket kept at constant temperature, Tj. Fluid velocity is plug shaped , in other words uniform at radial positions. Assume that temperature is uniform in radial positions because of turbulent flow conditions; ρ and Cp of the fluid are constants. The inlet temperature (at z=0) is constant and uniform at To (To>Tj). Assume that thermal conduction of heat along the...

Water in pipe AB (Figure 2), diameter (DAB) 1.2 m, is flowing with the velocity (VAB)...

Water in pipe AB (Figure 2), diameter (DAB) 1.2 m, is flowing with the velocity (VAB) of 3 m/second. Then it continues to flow through pipe BC, with a diameter (DBC) of 1.5 m and finally flows through branch pipe of CD, diameter (DCD) of 0.8 m and pipe of CE (DCE), with a velocity (VCE) of 2.1 m/second. Calculate: 1. Discharge of pipe AB (QAB) 2. Flow velocity of pipe BC (VBC) 3. Flow velocity of pipe BC (VBC)...

Air is flowing in a 1.5 m2 wind tunnel at 200 m/s at a pressure of...

Air is flowing in a 1.5 m2 wind tunnel at 200 m/s at a pressure of 250kPa, and temperature of 20°C at the entrance. Calculate: (i) Mach number (ii) Total Temperature (iii) Total Pressure (iv) Mass flow rate of air.

If a gas is flowing at 300m/s and has a pressure and temperature of 90kPa and...

If a gas is flowing at 300m/s and has a pressure and temperature of 90kPa and 20°C, find the maximum possible velocity that could be generated by expansion of this gas if the gas is air and if it is helium

Subjects