Question

In: Physics

Design and simulate a DC power supply using Zener diodes to produce 15 V if you...

Design and simulate a DC power supply using Zener diodes to produce 15 V if you have two Zener diodes of Zener voltage 7.5 V when the dc link voltage 24 V. The assignment report should include the following information: Assignment objectives, introduction, design procedure, simulation with simulation results, and conclusion.

Solutions

Expert Solution


Related Solutions

Design and simulate a regulated power supply using a bridge rectifier, capacitors, and zener diode (...
Design and simulate a regulated power supply using a bridge rectifier, capacitors, and zener diode ( no integrated circuit). The source voltage is 110 plus or minus 10 Vrms, 60 Hz frequency. The output voltage is as follows (plus or minus 5%) : 4.5 V and 12 V It has to be done on a breadboard. The rating of the adapter will be 12W and 5% regulation. To protect the circuit include a surge protection and fuse in the circuit...
design, simulate, and implement a 12W Multi Voltage AC/DC Adapter Switching Power Supply, Suitable for 3...
design, simulate, and implement a 12W Multi Voltage AC/DC Adapter Switching Power Supply, Suitable for 3 V to 12 V Device. Design Specifications: (a) Design and simulate a regulated power supply using bridge rectifier, capacitors, and Zener diode (no Integrated Circuit). The source voltage is 110±10 Vrms, 60 Hz  frequency. The output voltage is as follows (±5%): 3 V and 7.5V (b) The rating of the adapter will be 12W and 5% regulation. To protect your circuit include surge protection and...
Design a power supply to deliver 4 to 9 Vdc adjustable voltage to control DC motor...
Design a power supply to deliver 4 to 9 Vdc adjustable voltage to control DC motor speed. Motor power at maximum load is 20W at maximum speed (maximum voltage). Supply is 12V car battery with 70Ah capacity. How long the battery will last at maximum load and maximum speed? Add a 13.8Vdc communications power supply to continuously charge the battery at 500mA.
Design and simulate and fabrication a monostable multivibrators using 555 timer to produce a pulse width...
Design and simulate and fabrication a monostable multivibrators using 555 timer to produce a pulse width of 1 sec Calculate the freqency
An AC power supply produces a maximum voltage ΔVmax = 88 V. This power supply is...
An AC power supply produces a maximum voltage ΔVmax = 88 V. This power supply is connected to a resistor R = 27.0 Ω, and the current and resistor voltage are measured with an ideal AC ammeter and voltmeter as shown in the figure below. An ideal ammeter has zero resistance, and an ideal voltmeter has infinite resistance. (a) What is the reading on the ammeter? A (b) What is the reading on the voltmeter? V
An inductor used in a dc power supply has an inductance of 11.0 H and a...
An inductor used in a dc power supply has an inductance of 11.0 H and a resistance of 130 Ω. It carries a current of 0.550 A. What is the energy stored in the magnetic field? At what rate is thermal energy developed in the inductor? Part A What is the energy stored in the magnetic field? Part B At what rate is thermal energy developed in the inductor?
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60...
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60 Hz frequency. Please use online multisim and calculation
You are to design a 24-V, all-DC, stand-alone PV system to meet a 2.4 kWh/d demand...
You are to design a 24-V, all-DC, stand-alone PV system to meet a 2.4 kWh/d demand for a small, isolated cabin. You want to size the PV array to meet the load in a month with average insolation equal to 5.0 kWh/m 2/d
A 22.0 μF capacitor is charged by a 160.0-V power supply, then disconnected from the power...
A 22.0 μF capacitor is charged by a 160.0-V power supply, then disconnected from the power and connected in series with a 0.240-mH inductor. Calculate the energy stored in the inductor at t = 1.45 ms .
A quality control engineer wishes to estimate the mean output voltage of a DC power supply...
A quality control engineer wishes to estimate the mean output voltage of a DC power supply for different loads. The engineer measures output voltage when the supply is connected to 11 different loads and computes a mean 98.4 V and standard deviation 7 V. Assume that the output voltages follow a normal distribution. (a) Construct and interpret the 99.9% confidence interval. (b) Construct and interpret the 90% prediction interval.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT