Question
In: Electrical Engineering
design, simulate, and implement a 12W Multi Voltage AC/DC Adapter Switching Power Supply, Suitable for 3...
design, simulate, and implement a 12W Multi Voltage AC/DC Adapter Switching Power Supply, Suitable for 3 V to 12 V Device.
Design Specifications:
(a) Design and simulate a regulated power supply using bridge rectifier, capacitors, and Zener diode (no Integrated Circuit). The source voltage is 110±10 Vrms, 60 Hz frequency. The output voltage is as follows (±5%): 3 V and 7.5V
(b) The rating of the adapter will be 12W and 5% regulation. To protect your circuit include surge protection and fuse in the circuit design.
(c) Total number of element should be less than 12 for reducing environmental impact.
(d) Total Cost of the components of your design should be less than $10
please do it on a breadboard as well as on the multisim. provide pictures of the work done please. thank you.
Solutions
Manojponduru answered 2 years agoRelated Solutions
Design and simulate a DC power supply using Zener diodes to produce 15 V if you...
Design and simulate a DC power supply using Zener diodes to
produce 15 V if you have two Zener diodes of Zener voltage 7.5 V
when the dc link voltage 24 V. The assignment report should include
the following information: Assignment objectives, introduction,
design procedure, simulation with simulation results, and
conclusion.
Design a power supply to deliver 4 to 9 Vdc adjustable voltage to control DC motor...
Design a power supply to deliver 4 to 9 Vdc adjustable voltage
to control DC motor speed. Motor power at maximum load is 20W at
maximum speed (maximum voltage). Supply is 12V car battery with
70Ah capacity. How long the battery will last at maximum load and
maximum speed? Add a 13.8Vdc communications power supply to
continuously charge the battery at 500mA.
An AC power supply produces a maximum voltage ΔVmax = 88 V. This power supply is...
An AC power supply produces a maximum voltage ΔVmax = 88 V. This
power supply is connected to a resistor R = 27.0 Ω, and the current
and resistor voltage are measured with an ideal AC ammeter and
voltmeter as shown in the figure below. An ideal ammeter has zero
resistance, and an ideal voltmeter has infinite resistance.
(a) What is the reading on the
ammeter?
A
(b) What is the reading on the voltmeter?
V
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60...
Design and simulate a Half and Full wave rectifier for a
12V AC supply with 60 Hz frequency.
Please use online multisim
and calculation
A quality control engineer wishes to estimate the mean output voltage of a DC power supply...
A quality control engineer wishes to estimate the mean output
voltage of a DC power supply for different loads. The engineer
measures output voltage when the supply is connected to 11
different loads and computes a mean 98.4 V and standard deviation 7
V. Assume that the output voltages follow a normal
distribution.
(a) Construct and interpret the 99.9% confidence interval.
(b) Construct and interpret the 90% prediction interval.
Design and simulate a regulated power supply using a bridge rectifier, capacitors, and zener diode (...
Design and simulate a regulated power supply using a bridge
rectifier, capacitors, and zener diode ( no integrated circuit).
The source voltage is 110 plus or minus 10 Vrms, 60 Hz frequency.
The output voltage is as follows (plus or minus 5%) : 4.5 V and 12
V
It has to be done on a breadboard. The rating of the adapter
will be 12W and 5% regulation. To protect the circuit include a
surge protection and fuse in the circuit...
Design voltage x4 multiplier(Voltage quadrupler) if rms voltage of AC is 220V and frequency is 60Hz
Design voltage x4 multiplier(Voltage quadrupler) if
rms voltage of AC is 220V and frequency is 60Hz
Design an AC RLC circuit that can supply power to a load which is made up...
Design an AC RLC circuit that can supply power to a load which
is made up of an 8 - mu*F capacitor and a resistor with a
resistance that can be varied between 600 Q and 800 The average
power consumed by the circuit must be 2 kW or less and the power
factor must be above 0.95 for all conditions of the load. The
frequency of the power supply is 50 Hz. The design should include
an inductor and...
Design an AC RLC circuit that can supply power to a load which is made up...
Design an AC RLC circuit that can supply power to a load which
is made up of an 8 - mu*F capacitor and a resistor with a
resistance that can be varied between 600 Q and 800 The average
power consumed by the circuit must be 2 kW or less and the power
factor must be above 0.95 for all conditions of the load. The
frequency of the power supply is 50 Hz. The design should include
an inductor and...
Design DC to AC Inverter for electric vehicles using (MATLAB/SIMULINK)
Design DC to AC Inverter for electric vehicles using
(MATLAB/SIMULINK)
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Case 7 of the textbook examines the rise of Wal-Mart as a corporate bohemoth. One of...
- The type of listening that involves trying to understand a situation from the speaker’s perspective is...
- Based on the loanable funds theory, explain how each of the following changes should impact interest...
- research paper: each student will be responsible for writing an argumentative research paper discussion a topic...
- In java based on the classes provided finish the program per the requirements: ----------------------------------------------Class1 package cardgame;...
- Identify two cultures and analyze the nurturing process within each culture and discuss the impact the...
- Digital security is an increasing concern is the Internet age. In order to protect sensitive information...
ADVERTISEMENT