Question

In: Electrical Engineering

with a voltage range of 0.874 and -0.855 how can i design a inverting amplifier using...

with a voltage range of 0.874 and -0.855 how can i design a inverting amplifier using standard resistors to produce a voltage output range of -10 to 10 volts?

Solutions

Expert Solution

Note : In this , the maximum output of any op amp is actually depends on the value of DC supply given to them.so, kindly give the op- amp with +10v and -10v suppl. So, that you will get output in that range. And also put Rf=12kohm and R1= 1kohm.

If you have any doubts, kindly comment below. I will be happy to help you.


Related Solutions

Operational amplifier question Design a non- inverting amplifier with gain of 7.5?
Operational amplifier question Design a non- inverting amplifier with gain of 7.5?
3. Use matlab to plot the output voltage of an inverting operational amplifier given the following...
3. Use matlab to plot the output voltage of an inverting operational amplifier given the following conditions: K = Gain of the amplifier = 12.5. Vi = input voltage -2.5 < Vi < 2.5 V], (use 0.25 increments). V+ = positive power supply voltage, V+ = +20 V. V- = negative power supply voltage V- = -20V. Vo = output voltage Vo = -KVi Recall that if the output voltage Vo is greater than V+, or less than V-, the...
1.If an inverting voltage amplifier with a large gain were built to amplify a small sinusoidal...
1.If an inverting voltage amplifier with a large gain were built to amplify a small sinusoidal signal and the output waveform was observed to be sinusoidal but with a much lower amplitude than predicted by a theoretical analysis assuming an ideal operational amplifier, what non ideal property of the operational amplifier would be likely contributing to this degradation in performance? 40
Design a complete single-stage amplifier using transistor to amplifier a sine-wave voltage signal with an amplitude...
Design a complete single-stage amplifier using transistor to amplifier a sine-wave voltage signal with an amplitude of 2 mV, frequency range from 20-20kHz and internal resistance of 1k ohm. the output of the amplifier supplies to a load of 5k ohm and the required voltage amplitude around 300 mV.
Explain the operation of the isolation amplifier. Design a circuit that takes an input voltage and...
Explain the operation of the isolation amplifier. Design a circuit that takes an input voltage and outputs a scaled differentiated version of the input minus a scaled version of the input, at the output of the circuit
In a differential amplifier, the noninverting input is 3cos(600t + 45°) mV and the inverting input...
In a differential amplifier, the noninverting input is 3cos(600t + 45°) mV and the inverting input is 4cos (600t - 45°) mV. The ooutput is vo = 3cos (600t - 45°) + 4.004cos (600t - 45°) V. The CMRR is of? The unit must be in dB. Is vo= 3cos(600t + 45 ◦ ) + 4.004cos(600t - 45◦) V instead of: vo = 3cos(600t - 45 ◦ ) + 4.004cos(600t - 45 ◦ ) V
Derive the K value for the non-inverting amplifier (a) and the Summer (b) (use the naming...
Derive the K value for the non-inverting amplifier (a) and the Summer (b) (use the naming conventions from sheet in the back of the text).
In a differential amplifier, the non-inverting input is 3 cos (600t + 45◦) mV and the...
In a differential amplifier, the non-inverting input is 3 cos (600t + 45◦) mV and the inverting input is 4cos (600t - 45◦) mV. The output is vo = 3cos (600t + 45◦) + 4.004cos (600t - 45◦) V. The CMRR is of ____ dB
Problem 5. (10 pts) In a differential amplifier, the non-inverting input is 3 cos (600t +...
Problem 5. (10 pts) In a differential amplifier, the non-inverting input is 3 cos (600t + 45◦) mV and the inverting input is 4cos (600t - 45◦) mV. The output is vo = 3cos (600t + 45◦) + 4.004cos (600t - 45◦) V. The CMRR is dB
Design an ECG amplifier using 3 operational amplifiers for standard (AHA) specifications.
Design an ECG amplifier using 3 operational amplifiers for standard (AHA) specifications.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT