Assuming a characteristic impedance of 75 Ω and a load impedance of 100Ω, ﬁnd the input...

Assuming a characteristic impedance of 75 Ω and a load impedance of 100Ω, ﬁnd the input
impedance at λ/2, λ and 2λ. How each input impedance will vary for the case of: i) matched
line; ii) short-circuit line; iii) open circuit line?

Expert Solution

Manojponduru answered 9 months ago

The characteristic impedance of a two wire cable is 100 Ω and the VSWR on the...

The characteristic impedance of a two wire cable is 100 Ω and the VSWR on the line is 3. The cable is 60 cm long. The frequency of the signal on the line is 90 MHz .If the line is terminated by an antenna having impedance of 70 + jX Ω, where X is unknown, use Smith Chart to: a. Calculate load admittance. b. Calculate the impedance at a distance of 37.5 cm from the load; c. Design an open...

Assuming that the length of a lossless transmission line with the normalized load impedance of zL...

Assuming that the length of a lossless transmission line with the normalized load impedance of zL = ZL/Z0 = 1 + j1 is l = 2.25λz , there are a total of (A) 2 voltage maxima and 2 voltage minima (B) 2 voltage maxima and 3 voltage minima (C) 3 voltage maxima and 2 voltage minima (D) 4 voltage maxima and 4 voltage minima (E) 4 voltage maxima and 5 voltage minima (F) 5 voltage maxima and 4 voltage minima...

(Use Smith Chart) A 50 Ω line is terminated by a 75 Ω resistor. The input...

(Use Smith Chart) A 50 Ω line is terminated by a 75 Ω resistor. The input terminals are connected to the output terminals of a 30 Ω line. Both lines are 0.12 λ long. a. Find Zin and Γin at the input of the 30 Ω line b. SWR values on both lines Use Smith Chart

An input transmission line of characteristic impedance Z01 splits off into three identical output transmission lines...

An input transmission line of characteristic impedance Z01 splits off into three identical output transmission lines having characteristic impedance Z02 = 3Z01. This represents a four-port system. Find all 16 of the S parameters for this system. Note: Many of the 16 Sij parameters will be identical. There should be only four values that are distinct. SHOW WORK!!

AC Thevenin has an impedance of Zt = 6 + j75 What is the load impedance...

AC Thevenin has an impedance of Zt = 6 + j75 What is the load impedance for MPT? If a resistor was connected as load, what would the R value need to be for MPT?

Assume that R1 = 44 Ω , R2 = 75 Ω , R3 = 19 Ω...

Assume that R1 = 44 Ω , R2 = 75 Ω , R3 = 19 Ω , R4 = 79 Ω , R5 = 20 Ω , and R6 = 23 Ω . fig 1 fig 2 fig 3 fig 4 Part A Find the equivalent resistance of the combination shown in the figure (Figure 1) . Express your answer using two significant figures. Req =______ Ω Part B Find the equivalent resistance of the combination shown in the figure...

An amplifier with an output impedance of 75 ? is connected to a filter with a...

An amplifier with an output impedance of 75 ? is connected to a filter with a characteristic impedance of 60 – 20j ?. Design a single shunt stub matching network using an open circuit for a frequency of 500 MHz. Show ALL calculations. a) Calculate the normalized load admittance. b) Determine the distance (in ?) to the stub in the direction of the generator. c) Determine the normalized input admittance of the stub. d) Calculate the susceptance of the stub....

A lossless 60 Ω line is terminated by a (60 + j60) Ω load. (a) Find...

A lossless 60 Ω line is terminated by a (60 + j60) Ω load. (a) Find Γ and VSWR. (b) If Zin = 120 - j60 Ω, how far (in terms of wavelengths) is the load from the generator? (c) What fraction of the voltage is reflected? (d) What fraction of the current is reflected? (e) What fraction of the power is reflected?

3. A lossless 60 Ω line is terminated by a (60 + j60) Ω load. (a)...

3. A lossless 60 Ω line is terminated by a (60 + j60) Ω load. (a) Find Γ and VSWR. (b) If Zin = 120 - j60 Ω, how far (in terms of wavelengths) is the load from the generator? (c) What fraction of the voltage is reflected? (d) What fraction of the current is reflected? Solve by using smith charts

I think I have a little bit of understanding of input impedance impedance, but please check...

I think I have a little bit of understanding of input impedance impedance, but please check my understanding, and also explain physically what output impedance and reactance is AND EXPLAIN YOUR TERMINOLOGY or use basic af terminology: Input impedance describes (I think) a voltage source, or something that produces an output voltage, and its impedance within it's own circuitry. In other words, say I have a function generator, something supposed to output voltage, and the input impedance would be the...

Question