Question

In: Other

An orifice meter is used to measure flow rate of liquid in pipe shows a pressure...

An orifice meter is used to measure flow rate of liquid in pipe shows a pressure difference of ' x ' m of water column when the flow rate is Q If flow rate is doubled then what is delta P?

Solutions

Expert Solution


Related Solutions

A 75‐mm‐diameter orifice with D and D/2 taps is used to measure the flow rate of...
A 75‐mm‐diameter orifice with D and D/2 taps is used to measure the flow rate of 65°C water in a 150‐mm‐ID pipe. Determine the pressure difference for a flow rate of 20 L/s
how does the rotameter (flow meter) measure volumetric flow rate of air in the system?explain using...
how does the rotameter (flow meter) measure volumetric flow rate of air in the system?explain using a digram and 2-3 sentence discussion of the forces acting on the rotameter ball.
A pipe is carrying liquid at 60 degrees C, that fluctuates in pressure from 0 to...
A pipe is carrying liquid at 60 degrees C, that fluctuates in pressure from 0 to 60,000 kPa (non-capped). The inside diameter of the pipe is 20 mm and the wall thickness is 1 mm and is made out of 1095 carbon steel, has a yield strength of 813 MPa and an ultimate tensile strength of 1260 MPa. Using the "Modified-Goodman" failure criteria and a reliability factor of 99%, determine the number of cycles till failure on the inside wall....
Venturi-meter used to calculate the pressure in network pipes.? true or false
Venturi-meter used to calculate the pressure in network pipes.? true or false
6. An increase in roughness of a pipe with laminar flow would increase the pressure drop...
6. An increase in roughness of a pipe with laminar flow would increase the pressure drop of the pipe. Assume the velocity is the same for the smooth pipe and the rough pipe. a. True b. False
A 90o v-notch weir is used to measure discharge flow rate. A head (H) of 6...
A 90o v-notch weir is used to measure discharge flow rate. A head (H) of 6 inches is measured behind the weir. Assume the following: Weir equation is Q = 2.5H2.5 (Q in cfs and H in feet) 1 cfs = 450 gpm a) Estimate discharge flow rate in gallons per minute (gpm) b) Briefly describe hydraulic principle of open channel flow measurement Please show all work. Thank you so much in advance!
Water moves through a constricted pipe in steady, ideal flow. The pressure is 1.80 ✕ 105...
Water moves through a constricted pipe in steady, ideal flow. The pressure is 1.80 ✕ 105 Pa and the pipe radius is 2.90 cm. At the higher point located at y = 2.50 m, the pressure is 1.30 ✕ 105 Pa and the pipe radius is 1.60 cm. (a) Find the speed of flow in the lower section. m/s (b) Find the speed of flow in the upper section. m/s (c) Find the volume flow rate through the pipe. m3/s
A reducing elbow in a horizontal pipe is used to deflect water flow by an angle...
A reducing elbow in a horizontal pipe is used to deflect water flow by an angle θ = 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross-sectional area of the elbow is 150 cm2 at the inlet and 25 cm2 at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 57 kg. Determine...
Saturated liquid water at 1 MPa enters a D = 5 cm pipe at a rate...
Saturated liquid water at 1 MPa enters a D = 5 cm pipe at a rate of m(dot) = 2 kg/s. Heat is transferred to the water at a rate of Q(dot) = 5000 kW. The exit is at 1 MPa pressure. (a) Neglecting kinetic energy, calculate the temperature at the pipe exit. (ans = 400◦C) (b) Using your answer in a), calculate the exit velocity of the water. (ans = 312 m/s) (c) Based upon your answer, should kinetic...
Find the diameter of a pipe of length ‘X’ when the rate of flow of water...
Find the diameter of a pipe of length ‘X’ when the rate of flow of water through the pipe is ‘Q’ and the head lost due to friction is ‘4X’. Take the value of C = 1 in Chezy’s formula. Illustrate the resut of diameter of pipe and also conclude the discharge value for varying cross section of pipe, and the relationship between diameter of pipe and pressure of flow.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT