A reducing elbow in a horizontal pipe is used to deflect water flow by an angle...

A reducing elbow in a horizontal pipe is used to deflect water flow by an angle θ = 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 57 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. The density of water is 1000 kg/m³, and the flow rate of water is 30 kg/s

Expert Solution

Amanda K answered 5 months ago

Consider water flowing upwards through the 22.5o reducing elbow (22.5o angle to horizontal axis). If diameters...

Consider water flowing upwards through the 22.5o reducing elbow (22.5o angle to horizontal axis). If diameters of the elbow at entrance point and exit points are 0.02540 m and 0.01905 m respectively, elbow is 0.1 m high, velocities of water are 5 m/s and 9 m/s at entrance point and exit point respectively, and density of water is 1000 kg/m3, moment flux correction factor = 1.02. Determine gage pressure at inlet Determine vertical component of force of the system, if...

You are studying the laminar flow of water in a pipe at 20˚C. The pipe is...

You are studying the laminar flow of water in a pipe at 20˚C. The pipe is 2 cm in diameter, and the pressure gradient driving the flow is 0.8 Pa/m. Find the x-sectional average velocity (Poiseuille’s Law) and the maximum velocity achieved at the centerline of the pipe (use the equation for Umax presented in the alternative derivation of Poiseuille’s Law). How many times greater is the maximum velocity compared to the average velocity? Is this ū/umax ratio constant or...

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe...

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0 kPa and 25.0 kPa , respectively. What is the volume rate of flow?

Find the diameter of a pipe of length ‘X’ when the rate of flow of water...

Find the diameter of a pipe of length ‘X’ when the rate of flow of water through the pipe is ‘Q’ and the head lost due to friction is ‘4X’. Take the value of C = 1 in Chezy’s formula. Illustrate the resut of diameter of pipe and also conclude the discharge value for varying cross section of pipe, and the relationship between diameter of pipe and pressure of flow.

Water movinng in a horizontal pipe has a velocity of 9.0 m/s when the radius of...

Water movinng in a horizontal pipe has a velocity of 9.0 m/s when the radius of the pipe is 0.0025 metr. determine the velocity of the water when it enters a wider section of the pipe and the radius is 0.075 meter. Please show work Determine the density of a unkown smaple by using Archemdes Principle and water. the mass measurement of the sample in air is 200 grams, the mass measurement of the sample in water 147 grams. please...

Water is being pumped through a horizontal pipe that is 36.0 m long and 13.5 cm...

Water is being pumped through a horizontal pipe that is 36.0 m long and 13.5 cm in diameter. A pump maintains a gauge pressure of 742 Pa at a large open tank at one end of the pipe. The other end of the pipe is open to the air. If this pipe is replaced by a second one of length 9 m and diameter 5.0 cm, what gauge pressure must the pump provide to give the same volume flow rate...

Water flowing along a horizontal pipe has a speed of 2.31 m/s and a pressure of...

Water flowing along a horizontal pipe has a speed of 2.31 m/s and a pressure of 4.25 atm. Further along, the pipe narrows so that the cross-sectional area decreases by a factor of 6.17. What is the pressure in the narrow section?

The flowrate for water traveling through a horizontal 300 m-long cast iron pipe with a diameter...

The flowrate for water traveling through a horizontal 300 m-long cast iron pipe with a diameter of 0.6 m and a pressure drop of 17.2 kPa is to be found. P.S. use iterative approach to find values of f and then V using that f.

A horizontal pipe with a diameter of 4 inches abruptly connects to a larger pipe of...

A horizontal pipe with a diameter of 4 inches abruptly connects to a larger pipe of 12 inches in diameter in an industrial application. The flow is turbulent and the volume flow rate is 10 ft3/s in the smaller pipe and its pressure is 75 psia. The water temperature is 70-degrees Fahrenheit and the kinetic energy correction factor is 1.06 for the inlet and outlet connection. What is the loss coefficient, KL What is the head loss in feet What...

Water moves through a constricted pipe in steady, ideal flow. The pressure is 1.80 ✕ 105...

Water moves through a constricted pipe in steady, ideal flow. The pressure is 1.80 ✕ 105 Pa and the pipe radius is 2.90 cm. At the higher point located at y = 2.50 m, the pressure is 1.30 ✕ 105 Pa and the pipe radius is 1.60 cm. (a) Find the speed of flow in the lower section. m/s (b) Find the speed of flow in the upper section. m/s (c) Find the volume flow rate through the pipe. m3/s

Question