When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water....

When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water. The entrance and exit radii of the rotor are given as 0.05 m and 0.15 m respectively, the wing thickness at the entrance is 0.03 m, and the wing thickness at the exit is 0.01 m. The inlet and outlet vane angles are 60o and 45o respectively, and the pump mechanical efficiency is 0.85. In this case; a) What should be the theoretical head of the pump? b) What is the angle of flow between the absolute speed and the peripheral speed at the inlet? c) What power should be given to the shaft of the pump? (ρwater = 1000 kg / m3)

Expert Solution

samet mamat answered 1 year ago

A DC shunt motor drives a centrifugal pump at a speed of 1000 rpm when the...

A DC shunt motor drives a centrifugal pump at a speed of 1000 rpm when the terminal voltage and line currents are 200 V and 50 A, respectively. Given the armature resistance, Ra = 0.1 ohm and field resistance, Rf =100 ohm. Design a circuit which the speed of the motor can be controlled by using the added resistance method to the armature circuit and the maximum starting current is 120 A. Next, if the added resistance in the designed...

A centrifugal pump delivers water at rate of 0.22 m3/s from a reservoir at a ground...

A centrifugal pump delivers water at rate of 0.22 m3/s from a reservoir at a ground level to another reservoir to height 'h' through a vertical pipe of 0.2 m diameter. Both are open to atmosphere. Power input to pump is 90 kW and it operates with 75% efficiency . f=0.004 use g=9.8 m/s2 density=1000kg/m3. Find 'h'.

When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water.

When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water. At the same operating speed, best efficiency occurs at Q = 300 gpm, where the head is h = 21.9 ft of water. Fit these data at 1170 rpm with a parabola. Scale the results to a new operating speed of 1750 rpm. Plot and compare the results.

A centrifugal pump is to be used to pump water from a lake to a storage...

A centrifugal pump is to be used to pump water from a lake to a storage tank which is 165 feet above the surface of the lake. The pumping rate is to be 10 - 35 gal/min at a water temperature of 43°F. The water is used for drinking but will have to undergo filtration and chlorine treatment because there is sediment in the lake. The pump on hand can develop a discharge pressure of 60.0 psig pumping at a...

A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250...

A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250 GPM at 85 Fahrenheit water against 75 ft water head, assuming that the initial pump efficiency is 65 % doesn’t vary appreciably the maximum flow the pump can deliver is most nearly

2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure...

2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure rise and flow rate data while pumping water at room temperature: ?(dot)[m^3/s]= [0, 0.0278, 0.0417, 0.0556, 0.0694, 0.0833, 0.0903, 0.0972] ?P [kPa]= [361, 349, 328, 293, 230, 145, 114, 59] Estimate the pressure rise and flow rate for impeller speeds of 500 and 1000 rpm using the 750 rpm data. Plot pressure rise (y-axis) vs flow rate (x-axis) for all three pump speeds and...

A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit.

A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit. The vane width at inlet and exit are 25 and 10 mm respectively. The vane angles are ?1 = 500 and ?2 = 300. Assuming no prerotation at inlet and neglecting all sources of losses, determine a. the volume...

1. A turbo pump works at 1200 rpm rotation, with the ability to raise water as...

1. A turbo pump works at 1200 rpm rotation, with the ability to raise water as high as 200 m as much as 650 liters / minute, which is driven by an electric motor. But because the electric voltage should be 220 volts decreased so that the pump shaft spindle only 1000 rpm with the character of the pump. The pump efficiency assumption is 85%. a. How much power is needed if the voltage is still normal 220 volt. b....

1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm...

1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm and 1200 mm, and an inlet and exit blade thickness of 120 mm and 80 mm. The entering and exiting blade angles are 40o and 60o respectively. If the pump rotational speed is 575 rpm with and efficiency of 85%, determine: a) Ideal head (m) b) Fluid power for max pressure (kW) c) Shaft torque for max pressure (Nm) solutions a) 488 m b)...

A centrifugal pump lifts water against a head of 36m, the manometric efficiency being 80%. The...

A centrifugal pump lifts water against a head of 36m, the manometric efficiency being 80%. The suction and delivery pipes are both 150mm bore, the impeller is of 375mm and 25mm wide at the outlet; its exit blade angle is 250 and the specific rotational speed is 1320 rev/min. If the total loss by friction in the pipeline at this speed is estimated at 9m, calculate the probable rate of discharge at this speed.

Question