Question

In: Mechanical Engineering

A centrifugal pump lifts water against a head of 36m, the manometric efficiency being 80%. The...

A centrifugal pump lifts water against a head of 36m, the manometric efficiency being 80%. The suction and delivery pipes are both 150mm bore, the impeller is of 375mm and 25mm wide at the outlet; its exit blade angle is 250 and the specific rotational speed is 1320 rev/min. If the total loss by friction in the pipeline at this speed is estimated at 9m, calculate the probable rate of discharge at this speed.

Solutions

Expert Solution


Related Solutions

A centrifugal pump is to be used to pump water from a lake to a storage...
A centrifugal pump is to be used to pump water from a lake to a storage tank which is 165 feet above the surface of the lake. The pumping rate is to be 10 - 35 gal/min at a water temperature of 43°F. The water is used for drinking but will have to undergo filtration and chlorine treatment because there is sediment in the lake. The pump on hand can develop a discharge pressure of 60.0 psig pumping at a...
A pump lifts 1000 (liters) of water from ground to a tank on the roof of...
A pump lifts 1000 (liters) of water from ground to a tank on the roof of a building 100 (m) high. What is the potential energy in the water? [ 1 (liter) = 1000 cm3 ]. Show all your steps to the solution. A skier is coming downhill. At one point she is 50 (m) above the bottom of the hill and moving at 20 (m/s). What is her speed as she reaches the bottom of the hill? 22.3 (m/s)...
When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water.
When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water. At the same operating speed, best efficiency occurs at Q = 300 gpm, where the head is h = 21.9 ft of water. Fit these data at 1170 rpm with a parabola. Scale the results to a new operating speed of 1750 rpm. Plot and compare the results.  
What data is required to generate a pump curve (head versus flow rate and pump efficiency...
What data is required to generate a pump curve (head versus flow rate and pump efficiency versus flow rate) at different speeds ofa centrifugal pump?
1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm...
1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm and 1200 mm, and an inlet and exit blade thickness of 120 mm and 80 mm. The entering and exiting blade angles are 40o and 60o respectively. If the pump rotational speed is 575 rpm with and efficiency of 85%, determine: a) Ideal head (m) b) Fluid power for max pressure (kW) c) Shaft torque for max pressure (Nm) solutions a) 488 m b)...
When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water....
When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water. The entrance and exit radii of the rotor are given as 0.05 m and 0.15 m respectively, the wing thickness at the entrance is 0.03 m, and the wing thickness at the exit is 0.01 m. The inlet and outlet vane angles are 60o and 45o respectively, and the pump mechanical efficiency is 0.85. In this case; a) What should be the theoretical head...
A centrifugal pump delivers water at rate of 0.22 m3/s from a reservoir at a ground...
A centrifugal pump delivers water at rate of 0.22 m3/s from a reservoir at a ground level to another reservoir to height 'h' through a vertical pipe of 0.2 m diameter. Both are open to atmosphere. Power input to pump is 90 kW and it operates with 75% efficiency . f=0.004 use g=9.8 m/s2 density=1000kg/m3. Find 'h'.
this is fluid mechanics question a)sketch performance curve of a pump on a head against volumetric...
this is fluid mechanics question a)sketch performance curve of a pump on a head against volumetric flow rate axis b) label shutoff and delivery points. c) on the same axis sketch a system curve and label operating point.
this is fluid mechanics question a)sketch performance curve of a pump on a head against volumetric...
this is fluid mechanics question a)sketch performance curve of a pump on a head against volumetric flow rate axis b) label shutoff and delivery points. c) on the same axis sketch a system curve and label operating point.
Consider a centrifugal water pump whose geometry and flow conditions are as follows: Impeller outlet radius...
Consider a centrifugal water pump whose geometry and flow conditions are as follows: Impeller outlet radius – 2.5 cm, impeller inlet radius – 1.8 cm, impeller outlet width – 1 cm, design speed – 1800 rpm, Design flow rate120 liters/min, Backward-curved vanes (outlet blade angles) – 60 deg. Assuming 100% efficiency, find: a) the total head, b) absolute and relative discharge velocities, c) theoretical power required at design flow rate and d) the theoretical pump curve
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT