Question

In: Mechanical Engineering

When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water.

When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water. At the same operating speed, best efficiency occurs at Q = 300 gpm, where the head is h = 21.9 ft of water. Fit these data at 1170 rpm with a parabola. Scale the results to a new operating speed of 1750 rpm. Plot and compare the results.

 

Solutions

Expert Solution


Related Solutions

When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water....
When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water. The entrance and exit radii of the rotor are given as 0.05 m and 0.15 m respectively, the wing thickness at the entrance is 0.03 m, and the wing thickness at the exit is 0.01 m. The inlet and outlet vane angles are 60o and 45o respectively, and the pump mechanical efficiency is 0.85. In this case; a) What should be the theoretical head...
2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure...
2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure rise and flow rate data while pumping water at room temperature: ?(dot)[m^3/s]= [0, 0.0278, 0.0417, 0.0556, 0.0694, 0.0833, 0.0903, 0.0972] ?P [kPa]= [361, 349, 328, 293, 230, 145, 114, 59] Estimate the pressure rise and flow rate for impeller speeds of 500 and 1000 rpm using the 750 rpm data. Plot pressure rise (y-axis) vs flow rate (x-axis) for all three pump speeds and...
A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit.
A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit. The vane width at inlet and exit are 25 and 10 mm respectively. The vane angles are ?1 = 500 and ?2 = 300. Assuming no prerotation at inlet and neglecting all sources of losses, determine a. the volume...
A centrifugal pump has the following characteristic: outer diameter of impeller 800 mm, width of impeller...
A centrifugal pump has the following characteristic: outer diameter of impeller 800 mm, width of impeller vanes at outlet 100 mm, angle of impeller vanes at outlet 40 o . The impeller runs at 550 rpm and delivers 0.98 m 3 /s of water under an effective head of 35 m. A 500 kW motor is used to drive the pump. Determine the manometric, mechanical and overall efficiencies of the pump. Assume water enters the impeller vanes radially at inlet....
1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm...
1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm and 1200 mm, and an inlet and exit blade thickness of 120 mm and 80 mm. The entering and exiting blade angles are 40o and 60o respectively. If the pump rotational speed is 575 rpm with and efficiency of 85%, determine: a) Ideal head (m) b) Fluid power for max pressure (kW) c) Shaft torque for max pressure (Nm) solutions a) 488 m b)...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600 mm respectively while running at 850 rpm. When rotating, the blade angle is measured at 35o at the outlet with considering the tangent. The flow velocity is limited at 5 m/s constantly. Determine the following; (a) inlet blade angle (b) outlet absolute velocity with its angle at outlet and (c) the manometric head.
Consider a centrifugal water pump whose geometry and flow conditions are as follows: Impeller outlet radius...
Consider a centrifugal water pump whose geometry and flow conditions are as follows: Impeller outlet radius – 2.5 cm, impeller inlet radius – 1.8 cm, impeller outlet width – 1 cm, design speed – 1800 rpm, Design flow rate120 liters/min, Backward-curved vanes (outlet blade angles) – 60 deg. Assuming 100% efficiency, find: a) the total head, b) absolute and relative discharge velocities, c) theoretical power required at design flow rate and d) the theoretical pump curve
A DC shunt motor drives a centrifugal pump at a speed of 1000 rpm when the...
A DC shunt motor drives a centrifugal pump at a speed of 1000 rpm when the terminal voltage and line currents are 200 V and 50 A, respectively. Given the armature resistance, Ra = 0.1 ohm and field resistance, Rf =100 ohm. Design a circuit which the speed of the motor can be controlled by using the added resistance method to the armature circuit and the maximum starting current is 120 A. Next, if the added resistance in the designed...
‏1. The impeller in a centrifugal pump has inner diameter as 125 mm and outer diameter...
‏1. The impeller in a centrifugal pump has inner diameter as 125 mm and outer diameter as 270 mm. The pump runs at 1400 rpm. The vane angles of impeller at inlet and outlet are 17° and 30° respectively. The water enters the impeller radially and velocity of flow is constant. Determine the work done by impeller per unit weight of water.
A centrifugal pump lifts water against a head of 36m, the manometric efficiency being 80%. The...
A centrifugal pump lifts water against a head of 36m, the manometric efficiency being 80%. The suction and delivery pipes are both 150mm bore, the impeller is of 375mm and 25mm wide at the outlet; its exit blade angle is 250 and the specific rotational speed is 1320 rev/min. If the total loss by friction in the pipeline at this speed is estimated at 9m, calculate the probable rate of discharge at this speed.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT