Question

In: Mechanical Engineering

1. A turbo pump works at 1200 rpm rotation, with the ability to raise water as...

1. A turbo pump works at 1200 rpm rotation, with the ability to raise water as high as 200 m as much as 650 liters / minute, which is driven by an electric motor. But because the electric voltage should be 220 volts decreased so that the pump shaft spindle only 1000 rpm with the character of the pump. The pump efficiency assumption is 85%.

a. How much power is needed if the voltage is still normal 220 volt.

b. With the actual condition of the pump turn down to 1000 rpm how much water can be drained if water remains to be raised as high as 200 m.

c. How much water can be raised if the amount of water remains as much as 650 liters / minute.

d. What is the power requirement in the actual condition.

Solutions

Expert Solution


Related Solutions

A catrifugal pump is operating at the rotation rate of 750 rpm. Pump is working at...
A catrifugal pump is operating at the rotation rate of 750 rpm. Pump is working at the design condition. Water leaves the blade at 40o from the radial direction. Water enters to blade at 80o from tangential direction( offdesign condition). The inner and outher radius of the impeller is 12 cm and 18 cm respectivelly. The width of the impeller is 14 cm. Flow rate of the pump is 0.60 m3/s. Draw the velocity triangles at inlet and outlet of...
When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water....
When a centrifugal pump runs at 1500 rpm, it discharges 0.05 m3 / h of water. The entrance and exit radii of the rotor are given as 0.05 m and 0.15 m respectively, the wing thickness at the entrance is 0.03 m, and the wing thickness at the exit is 0.01 m. The inlet and outlet vane angles are 60o and 45o respectively, and the pump mechanical efficiency is 0.85. In this case; a) What should be the theoretical head...
1. A 150-kg sewing machine operates at 1200 RPM and has a rotating unbalance of 0.45...
1. A 150-kg sewing machine operates at 1200 RPM and has a rotating unbalance of 0.45 kg-m. What is the max stiffness of an undamped isolator such that the force transmitted to the machine’s foundation is less than: a) 1547 b) 2547 2. Redesign helicopter seat (i.e. find new stiffness) so that the maximum velocity experienced by the pilot is 1 mm/sec.
1. One pump is not enough to pump water to a very high tank. If you...
1. One pump is not enough to pump water to a very high tank. If you use two pumps (to increase h), how are you going to install them? (a) in parallel (b) in series 2. For turbulent flow of all pipes, friction factor (f) depends on: (a) Reynolds number (Re) only (b) relative roughness (e/D) only (c) both Re and e/D 4. For a pumping system, which tends to cause cavitation? (a) placing the pump close to the source...
A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit.
A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit. The vane width at inlet and exit are 25 and 10 mm respectively. The vane angles are ?1 = 500 and ?2 = 300. Assuming no prerotation at inlet and neglecting all sources of losses, determine a. the volume...
When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water.
When operated at N = 1170 rpm, a centrifugal pump, with impeller D = 8in., has a shutoff head ho = 25.0 ft of water. At the same operating speed, best efficiency occurs at Q = 300 gpm, where the head is h = 21.9 ft of water. Fit these data at 1170 rpm with a parabola. Scale the results to a new operating speed of 1750 rpm. Plot and compare the results.  
2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure...
2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure rise and flow rate data while pumping water at room temperature: ?(dot)[m^3/s]= [0, 0.0278, 0.0417, 0.0556, 0.0694, 0.0833, 0.0903, 0.0972] ?P [kPa]= [361, 349, 328, 293, 230, 145, 114, 59] Estimate the pressure rise and flow rate for impeller speeds of 500 and 1000 rpm using the 750 rpm data. Plot pressure rise (y-axis) vs flow rate (x-axis) for all three pump speeds and...
1) A tank is full of water. Find the work W required to pump the water...
1) A tank is full of water. Find the work W required to pump the water out of the spout. (Use 9.8 m/s2 for g. Use 1000 kg/m3 as the weight density of water. Assume that a = 4 m, b = 4 m, c = 12 m,and d = 1 m.) W = ___ J I got 5017600 then in scientific notation it would be 5.0176 X 10^6, then in Juls in would be 5.02? I got the answer...
Note that 1 calorie (4.2 J) is the energy needed to raise 1 gram of water...
Note that 1 calorie (4.2 J) is the energy needed to raise 1 gram of water 1 degree, and recall that a food calorie is actually a kilocalorie Use whatever approximations you need, but state what they are.   Show your work. 1) How much ice water must you drink and so heat up to equal the energy in a chocolate glazed donut? 2) Will drinking ice water work as a weight loss strategy? 3) How about standing on a windy...
1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm...
1. A centrifugal water pump impeller is given an inlet and exit radius of 400 mm and 1200 mm, and an inlet and exit blade thickness of 120 mm and 80 mm. The entering and exiting blade angles are 40o and 60o respectively. If the pump rotational speed is 575 rpm with and efficiency of 85%, determine: a) Ideal head (m) b) Fluid power for max pressure (kW) c) Shaft torque for max pressure (Nm) solutions a) 488 m b)...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT