Question

In: Other

Outline of procedure: Dilute bleach solution A 1/10. Prepare analyte for titration by adding 10mL of...

Outline of procedure:

Dilute bleach solution A 1/10.

Prepare analyte for titration by adding 10mL of diluted bleach solution, indicator and 5mL of 2 M HCl.

Titrate the analyte with 0.05524 M Na2S2O3.

Average volume of Na2S2O3 added = 31.25 mL

Question: Calculate the percent of sodium hypochlorite in the original bleach bottle using your averaged result. Show the calculation for solution A only. Which bleach solution is the more potent cleaning agent?

Solutions

Expert Solution


Related Solutions

mass of Na2S2O3 is 1.220g titration of bleach with Na2S2O3 solution: trial 1: total volume used...
mass of Na2S2O3 is 1.220g titration of bleach with Na2S2O3 solution: trial 1: total volume used 66mL trial 2: total volume used 73.8mL Density of Bleach 1.074 kg/L a) find the moles of Na2S2O3 used to titrate the bleach solution b)find the moles of I2 formed by reaction with bleach c) find the molarity of OCl- present in the bleach solution d) find the grams of NaOCl present in the bleach e) find the percent NaOCl present in the bleach
A titration is a procedure for determining the concentration of a solution by allowing it to...
A titration is a procedure for determining the concentration of a solution by allowing it to react with another solution of known concentration (called a standard solution). Acid-base reactions and oxidation-reduction reactions are used in titrations. For example, to find the concentration of an HCl solution (an acid), a standard solution of NaOH (a base) is added to a measured volume of HCl from a calibrated tube called a buret. An indicator is also present and it will change color...
What was the initial concentration of 100ml of KBr solution, if after adding water to dilute...
What was the initial concentration of 100ml of KBr solution, if after adding water to dilute it, 300ml of a 4 percent solution was obtained?
A titration involves adding a reactant of known quantity to a solution of an another reactant...
A titration involves adding a reactant of known quantity to a solution of an another reactant while monitoring the equilibrium concentrations. This allows one to determine the concentration of the second reactant. The equation for the reaction of a generic weak acid HA with a strong base is HA(aq)+OH−(aq)→A−(aq)+H2O(l) A certain weak acid, HA, with a Ka value of 5.61×10−6, is titrated with NaOH. A solution is made by titrating 9.00 mmol (millimoles) of HA and 1.00 mmol of the...
Your supervisor wants you to dilute a 1 mL stock BSA solution (1 mg/mL) into 1:10...
Your supervisor wants you to dilute a 1 mL stock BSA solution (1 mg/mL) into 1:10 dilutions. What is the final concentration of diluted BSA solution? Show your work. How much volume (mL) of BSA and distilled water would you need to perform the dilution? Show your work.
The students swabbed each plate and set a filter paper disk with 10% bleach solution of...
The students swabbed each plate and set a filter paper disk with 10% bleach solution of differing ages on the plates for 10 minutes. The disks were removed and then the plates were incubated for 48 hours. The diameter of clearing was measured for each plate. Create a Table, with title, in the results and then interpret the results in the discussion. Notice how some areas of clearing show individual colonies. What mechanisms may allow for that growth within a...
10. A titration is performed by adding 0.13 M KOH to 60 mL of 0.363 M...
10. A titration is performed by adding 0.13 M KOH to 60 mL of 0.363 M HNO3. a) Calculate the pH before addition of any KOH. b) Calculate the pH after the addition of 33.51, 83.77 and 166.54 mL of the base.(Show your work in detail for one of the volumes.) c) Calculate the volume of base needed to reach the equivalence point. d) Calculate the pH after adding 5.00 mL of KOH past the equivalence point.
1- In the titration between potassium iodate and the sodium thiosulfate solution, if the titration is...
1- In the titration between potassium iodate and the sodium thiosulfate solution, if the titration is not performed immediately after the addition of the sulfuric acid, how would this likely affect the calculated concentration of your diluted sodium thiosulfate solution? 2- Why did the titrations performed need to be started immediately after adding the sulfuric acid? 3- A sample of bleach was analyzed as in this procedure. The only procedural difference is that the student weighed out the bleach solution...
1. Which item of volumetric equipment should be use to: a. measure approximately 10mL of solution?...
1. Which item of volumetric equipment should be use to: a. measure approximately 10mL of solution? b. measure 10.10mL of solution? 2. Why is it necessary to rinse a buret or pipet with the liquid to be measured? 3. Indicate whether the following errors are random or systematic. a. The graduation mark on a pipet is incorrect by +0.11mL. b. Three students read a buret and obtain values of 25.10, 25.12, and 25.09ml. c. The balance is not zeroed and...
A precipitation titration was performed by adding 0.20 M Ag+ (from standard silver nitrate solution) from...
A precipitation titration was performed by adding 0.20 M Ag+ (from standard silver nitrate solution) from a buret into 40.0 mL mixture of 0.10 M I- (as NaI) and 0.10 M Cl- (as NaCl). Calculate the concentration of Ag+, I-, Cl-, Na+, and NO3- when (a) 0.0 mL, (b) 10.0 mL, (c) 20.0 mL, (d) 30.0 mL, (d) 40.0 mL, and (d) 50.0 mL of Ag+ were added. (Given Ksp AgI = 8.3 x 10-17 and Ksp AgCl = 1.8...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT