Select the lightest W10 section. Using Fy=50ksi and Fu= 65ksi to select trial sizes and check...

Select the lightest W10 section. Using Fy=50ksi and Fu= 65ksi to select trial sizes and check for Gross Section Yielding and Tensile Rupture. Assume the member is to have two lines of bolts in each flange. (use ASD method)

Pd - dead load = 225 ksi
Pl - live load = 150 ksi
L - member length = 28 ft
Bolt diameter = 7/8 in

Select the lightest W12 not W10.

Expert Solution

Ally Wells answered 1 year ago

Select the lightest W12 for the conditions described, using Fy = 50 ksi and Fu =...

Select the lightest W12 for the conditions described, using Fy = 50 ksi and Fu = 65ksi. Show calculations to select trial sizes and check for Gross Section Yielding and Tensile Rupture. Assume the member is to have two lines of 7/8" bolts in each flange. use LRFD method PD= 225 PL=150 Length= 28'

Select the lightest W-section for bending, Cb=1 MD = 60 k-ft ML = 40 k-ft Fy=...

Select the lightest W-section for bending, Cb=1 MD = 60 k-ft ML = 40 k-ft Fy= 50 ksi Lb=10ft

Design the lightest W16 tension member section of steel of Fy= 50 ksi, Fu= 65 ksi...

Design the lightest W16 tension member section of steel of Fy= 50 ksi, Fu= 65 ksi to support a tensile service dead load PD = 270 k and a tensile service load PL= 220 k. the member is to be 53 ft. long the member is to have two lines of bolts in each flange for 7/8-in bolts (there are three in a line 4 in on center). At the end you should make the necessary checks. ACI Code

Select the lightest W section to serve as an axially loaded column 28 ft long, in...

Select the lightest W section to serve as an axially loaded column 28 ft long, in a braced frame, with additional lateral support in the weak direction at mid-height. The load to be carried is 65 kips dead load and 150 kips live load. Assume the top and bottom of the column are hinged. a) Use A992 and indicate first and second choices b) Use A572 Grade 60, indicating first and second choices

Select the lightest W14 section to carry an axial compression of P = 100 kips dead...

Select the lightest W14 section to carry an axial compression of P = 100 kips dead load, and 140 kips live load; along with a strong axis bending moment of 125 kip-ft dead load and 325 kip-ft live load. Assume the moment acts along the entire 15 foot length of the member, and the ends are pin-pin connections.

Select lightest section, neglect bock shear. Given a WT6 with D = 80k, L = 120k, ...

Select lightest section, neglect bock shear. Given a WT6 with D = 80k, L = 120k, length 20 feet, A992 steel. The end connection is a longitudinal weld to flange only (weld on each longitudinal edge of flange) and it is 6 in. long.

Select the Lightest weight W-section of A992 steel to serve as a column 30 feet long...

Select the Lightest weight W-section of A992 steel to serve as a column 30 feet long and to carry an axial live compressive load of 160 kips. The member is pinned at the top and bottom. The member's self weight is estimated at 2000 lbs. It is supported at mid-height in its weak direction,

(1) Select the lightest, rectangular Douglas fir section for the cantilever beam of15- ft span that...

(1) Select the lightest, rectangular Douglas fir section for the cantilever beam of15- ft span that will carry a uniform load of 450 lb/ft. [Hint: V max = wL; Mmax = wL2/2]

Select the Lightest weight W-section of A992 steel to serve as a column 30 feet long...

Select the Lightest weight W-section of A992 steel to serve as a column 30 feet long and to carry an axial live compressive load of 160 kips. The member is pinned at the top and bottom. The member's self weight is estimated at 2000 lbs. It is supported at mid-height in its weak direction. Options: 1.W8x40 2.W10x39 3.W12x45 4.W14x48 5.W14x53 6.W10x45

1) Select the lightest section to support a axial load (DL=700 kips y LL= 300 kips)....

1) Select the lightest section to support a axial load (DL=700 kips y LL= 300 kips). The element is braced, so LX= 22 ft and LY= 12 ft. The end support conditions are: a) (Fixed/pinned) and it is specified to use A572 gr. 60. (verify slenderness and local buckling) b) (Fixed/Fixed) and you must use A-36

Question

Select the lightest W10 section. Using Fy=50ksi and Fu= 65ksi to select trial sizes and check...

Solutions

Expert Solution

Related Solutions

Select the lightest W12 for the conditions described, using Fy = 50 ksi and Fu =...

Select the lightest W-section for bending, Cb=1 MD = 60 k-ft ML = 40 k-ft Fy=...

Design the lightest W16 tension member section of steel of Fy= 50 ksi, Fu= 65 ksi...

Select the lightest W section to serve as an axially loaded column 28 ft long, in...

Select the lightest W14 section to carry an axial compression of P = 100 kips dead...

Select lightest section, neglect bock shear. Given a WT6 with D = 80k, L = 120k, ...

Select the Lightest weight W-section of A992 steel to serve as a column 30 feet long...

(1) Select the lightest, rectangular Douglas fir section for the cantilever beam of15- ft span that...

Select the Lightest weight W-section of A992 steel to serve as a column 30 feet long...

1) Select the lightest section to support a axial load (DL=700 kips y LL= 300 kips)....