A venturimeter is placed in a pipe which is at 30 degrees to the horizontal. The...

A venturimeter is placed in a pipe which is at 30 degrees to the horizontal. The pipe carries gasoline of specific gravity 0.8. The diameter at inlet and throat diameter are 5cm and 3cm respectively. A mercury manometer reads a level difference of 10cm.Calculate the flow rate.

Expert Solution

samet mamat answered 2 years ago

A block is placed on a plane inclined at 35 degrees relative to the horizontal. If...

A block is placed on a plane inclined at 35 degrees relative to the horizontal. If the bloc k slides down the plane with an acceleration of magnitude g/3, determine the coefficient of the kinetic friction between the block and plane.

A cannon is shot at 48 m/s at an angle of 30 degrees to the horizontal...

A cannon is shot at 48 m/s at an angle of 30 degrees to the horizontal off a cliff that is 78.4 meters tall. How fast will the cannonball be moving when it hits the ground at the bottom of the cliff?

A cannonball at ground level is aimed 30 degrees above the horizontal and is fired with...

A cannonball at ground level is aimed 30 degrees above the horizontal and is fired with an initial speed of 125 m/s. A) how far away from the cannon will the cannonball hit the ground? B) What is the highest point of its trajectory?

A 4.0-kg block is on an incline plane of 30 degrees angle with respect to horizontal....

A 4.0-kg block is on an incline plane of 30 degrees angle with respect to horizontal. a)What is the minimum coefficient of static friction (μs)min is need to prevent it from sliding down? b) If the surface μs is 0.30, less than (μs)min now, how much force(F) is needed to apply to the block horizontally to prevent it from sliding down?c) If F is doubled, what’s the acceleration of the block up the incline? Assume the coefficient of kinetic friction...

A horizontal pipe with a diameter of 4 inches abruptly connects to a larger pipe of...

A horizontal pipe with a diameter of 4 inches abruptly connects to a larger pipe of 12 inches in diameter in an industrial application. The flow is turbulent and the volume flow rate is 10 ft3/s in the smaller pipe and its pressure is 75 psia. The water temperature is 70-degrees Fahrenheit and the kinetic energy correction factor is 1.06 for the inlet and outlet connection. What is the loss coefficient, KL What is the head loss in feet What...

A 600’ long sewer pipe is being placed into a trench. Place the pipe at a...

A 600’ long sewer pipe is being placed into a trench. Place the pipe at a gravity drainage slope of 2% towards station 6+00. The invert elevation at its beginning station (0+00) is 5395.00’. The pipe has an outside diameter of 1’ and a wall thickness of 1”. a) Prepare an Excel table that lists the elevations for the top of the pipe for the stations 0+00, 1+00, 2+00, 3+00, 4+00, 5+00 and 6+00 *. b) Calculate the invert elevation...

An incompressible liquid flows through a straight horizontal pipe. Friction of the fluid within the pipe...

An incompressible liquid flows through a straight horizontal pipe. Friction of the fluid within the pipe causes a small amount of heat to be transferred from the fluid; to compensate, flow work must be done on the fluid to move it through the system (so W(dot)fl is greater than zero. a) How are V(dot)in and V(dot)out related, where V(dot) is the volumetric flow rate of the liquid? (Remember, fluid is incompressible) b) How must the pressures of Pin and Pout...

(1) A block is placed on a wooden plank, which is initially horizontal. One end of...

(1) A block is placed on a wooden plank, which is initially horizontal. One end of the plank is slowly raised to make it more and more inclined, and for a while the block stays in place on the plank and doesn't slide due to static friction. Finally, when the plank reaches an incline of 56.3o above horizontal, the block begins to slide. What is the coefficient of static friction between the block and the plank? (2) Continuing the story... after...

You are standing on a slope of 20 degrees to the horizontal and are going to...

You are standing on a slope of 20 degrees to the horizontal and are going to throw a ball at vi=20 m/s up the incline. If you throw the ball at an angle of 45 degrees with respect to the horizontal at what distance up the incline from your feet does it land? Assume the ball leaves your hand directly overhead, h=2.0 m above the slope. I know the horizontal velocity = 14.14 m/s and the vertical velocity also =...

A 2.20-kg object is attached to a spring and placed on frictionless, horizontal surface. A horizontal...

A 2.20-kg object is attached to a spring and placed on frictionless, horizontal surface. A horizontal force of 18.0 N is required to hold the object at rest when it is pulled 0.200 m from its equilibrium position (the origin of the x axis). The object is now released from rest from this stretched position, and it subsequently undergoes simple harmonic oscillations. (a) Find the force constant of the spring. N/m (b) Find the frequency of the oscillations. Hz (c)...

Question