Question

In: Mechanical Engineering

A horizontal pipe with a diameter of 4 inches abruptly connects to a larger pipe of...

A horizontal pipe with a diameter of 4 inches abruptly connects to a larger pipe of 12 inches in diameter in an industrial application.

The flow is turbulent and the volume flow rate is 10 ft3/s in the smaller pipe and its pressure is 75 psia. The water temperature is 70-degrees Fahrenheit and the kinetic energy correction factor is 1.06 for the inlet and outlet connection.
What is the loss coefficient, KL
What is the head loss in feet
What is the pressure in the larger pipe downstream from the transition in psia

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

The diameter of the discharge and suction pipe of a boiler feed pump is 4 inches...
The diameter of the discharge and suction pipe of a boiler feed pump is 4 inches and 6 inches, respectively. The water delivered is 250 GPM and the temperature is 60 F. The discharge pressure near the pump is 90 psig and the suction is 12 in.hg vacuum. Find the total dynamic head if the discharge gage is located 3 ft above pump centerline and the vacuum gage connection to the suction pipe is 2 feet below the center of...
Question 1) As water passes from a pipe of larger diameter to a pipe of smaller...
Question 1) As water passes from a pipe of larger diameter to a pipe of smaller diameter in converging section, the static pressure: Becomes half Increases Decreases Does not change Question 2) The following reading have to be recorded from the flow measurement apparatus to calculate the mass flow rate from the venturimeter? Pressures at the inlet and exit of the venturimeter Pressures at the inlet and throat of the venturimeter The rotameter reading venturimeter The pressure at the throat...
A horizontal pipe of diameter 0.768 m has a smooth constriction to a section of diameter...
A horizontal pipe of diameter 0.768 m has a smooth constriction to a section of diameter 0.4608 m. The density of oil flowing in the pipe is 821 kg/m3 . If the pressure in the pipe is 7120 N/m2 and in the constricted section is 5340 N/m2 , what is the rate at which oil is flowing? Answer in units of m3/s.
A horizontal pipe 10 cm in diameter and 3000 cm long is filled with a sand...
A horizontal pipe 10 cm in diameter and 3000 cm long is filled with a sand of 20 % porosity. The permeability of the sand is estimated to be 250 md. The sand is saturated with an oil of viscosity 0.65 cp, and the same oil is injected into the sand pipe. You are asked to calculate a. What is the Darcy velocity in the sand pipe under a 100-psi pressure differential? b. What is the flow rate through the...
Methane gas enters a horizontal pipe with a thin wall of 25 cm diameter at a...
Methane gas enters a horizontal pipe with a thin wall of 25 cm diameter at a temperature of 309 C with 4.5 tons of mass flow per hour and exits at 289 C. The pipe is smooth and its length is 10 m and the ambient and environmental temperature is 25 C. Since the smear coefficient of the pipe surface is given as 0.8; a-) Indoor and outdoor convection coefficients (W / m2K), b-) Heat loss from the pipe to...
A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe...
A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0 kPa and 25.0 kPa , respectively. What is the volume rate of flow?
Crude oil of density 970 kg.m-3 flows in a pipe of internal diameter 9 inches and...
Crude oil of density 970 kg.m-3 flows in a pipe of internal diameter 9 inches and circular section that exhibits a 90° bend in the horizontal plane. The flowrate of the oil is 11,000 litres per minute. Calculate the force imparted by the oil on the bend due to the change of momentum of the fluid, and draw a diagram to indicate the direction of this force.
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the...
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the production quality, you sample 30 gears and find the average to be 4.11 with a standard deviation of 0.67. Construct a hypothesis test at a 0.05 level of significance to determine if the gear diameter is larger than 4 inches. Select one: a. The critical value is 2.05, the test statistic is 0.90, conclude the gear diameter is not equal to 4 inches b....
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the...
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the production quality, you sample 30 gears and find the average to be 4.08 with a standard deviation of 0.71. Construct a hypothesis test at a 0.05 level of significance to determine if the gear diameter is larger than 4 inches. Select one: a. The critical value is 1.70, the test statistic is 0.62, conclude the gear diameter is less than or equal to 4...
Steam enters a horizontal 15-cm-diameter pipe as a saturated vapor at 5 bar with a velocity...
Steam enters a horizontal 15-cm-diameter pipe as a saturated vapor at 5 bar with a velocity of 10 m/s and exits at 4.5 bar with a quality of 95%. Heat transfer from the pipe to the surroundings at 300K takes place at an average outer surface temperature of 400 K. For operation at steady state, determine (a) the velocity at the exit, in m/s. (b) the rate of heat transfer from the pipe, in kW. (c) the rate of entropy...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT