Question

In: Mechanical Engineering

At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits...

At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits snugly over a steel hoop 15 mm thick. Both hoops are 100 mm wide. Compute the contact pressure between the hoops when the temperature drops to 20°C. Neglect the possibility that the inner ring may buckle. For steel, E = 200 GPa and α = 11.7μm/(m.°C). For bronze, E = 83 GPa α = 19 μm/(m.°C)

Solutions

Expert Solution


Related Solutions

At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits...
At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits snugly over a steel hoop 15 mm thick. Both hoops are 100 mm wide. Compute the contact pressure between the hoops when the temperature drops to 20°C. Neglect the possibility that the inner ring may buckle. For steel, E = 200 GPa and α = 11.7μm/(m.°C). For bronze, E = 83 GPa α = 19 μm/(m.°C) At 130°C, a bronze hoop 20 mm thick...
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported...
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported over a span of 10 meters. Find the maximum bending stress in the pipe metal, when the pipe is running full. Take density of cast iron = 70.6 kN/m3 and water = 9.8 kN/m3
A 3-mm-diameter and 12-m-long electric wire is tightly wrapped with a 1.5-mm-thick plastic cover whose thermal...
A 3-mm-diameter and 12-m-long electric wire is tightly wrapped with a 1.5-mm-thick plastic cover whose thermal conductivity and emissivity are k 5 0.20 W/m·K and « 5 0.9. Electrical measurements indicate that a current of 10 A passes through the wire and there is a voltage drop of 7 V along the wire. If the insulated wire is exposed to calm atmospheric air at T` 5 30°C, determine the temperature at the interface of the wire and the plastic cover...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600 mm respectively while running at 850 rpm. When rotating, the blade angle is measured at 35o at the outlet with considering the tangent. The flow velocity is limited at 5 m/s constantly. Determine the following; (a) inlet blade angle (b) outlet absolute velocity with its angle at outlet and (c) the manometric head.
A neon sign is made of glass tubing whose inside diameter is 2.5 cm and whose...
A neon sign is made of glass tubing whose inside diameter is 2.5 cm and whose length is 5.5 m. If the sign contains neon at a pressure of 1.73 torr at 37 ∘C, how many grams of neon are in the sign? (The volume of a cylinder is πr2h.) Express your answer using two significant figures.
(c) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...
(c) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...
130 kg of uniform spherical particles with a diameter of 60 mm and particle density 1500...
130 kg of uniform spherical particles with a diameter of 60 mm and particle density 1500 kg/m3 are fludised by water (density 1000 kg/m3, viscosity 0.001 Pa s) in a circular bed of cross-sectional area 0.2 m2. The single particle terminal velocity of the particles is 0.98 mm/s and the voidage at incipient fludisation is known to be 0.47. Determine: a. The minimum fludised velocity             b. height when the liquid flow rate is 2x10-5 m3/s.  
130 kg of uniform spherical particles with a diameter of 60 mm and particle density 1500...
130 kg of uniform spherical particles with a diameter of 60 mm and particle density 1500 kg/m3 are fludised by water (density 1000 kg/m3, viscosity 0.001 Pa s) in a circular bed of cross-sectional area 0.2 m2. The single particle terminal velocity of the particles is 0.98 mm/s and the voidage at incipient fludisation is known to be 0.47. Determine: The minimum fludised velocity and the bed height at incipient fludisation.                                The mean fludised bed voidage and height when...
A 12-in-diameter well completely penetrates a 130-ft-thick, unconfined aquifer with a coefficient of permeability of 0.00055...
A 12-in-diameter well completely penetrates a 130-ft-thick, unconfined aquifer with a coefficient of permeability of 0.00055 ft/sec. If the radius of influence of the well is 500 feet and the drawdown at an observation well 250 ft away is 5 ft, determine the steady state well discharge and the drawdown at the well.
The propeller shaft of a large ship has an outside diameter of 350 mm and inside...
The propeller shaft of a large ship has an outside diameter of 350 mm and inside diameter 250mm. the shaft is rated for a maximum of shear stress 62 MPa. 1) if the shaft is runnning at 500 rpm what is the maximum power that can be transmitted without exceeding allowable stress. 2) if the rotational speed of the shaft is doubled but the power requirements unchanged what happens to the shear stress in the shaft? calculate valures.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT