Question

In: Physics

A transformer is intended to decrease the value of the alternating voltage from 500 volts to...

A transformer is intended to decrease the value of the alternating voltage from 500 volts to 25 volts. The primary coil contains 200 turns. Find the necessary number of turns N2 in the secondary coil.

A transformer is intended to decrease the value of the alternating current from 500 amperes to 25 amperes. The primary coil contains 200 turns. Find the necessary number of turns N2 in the secondary coil.

In a transformer, the primary coil contains 400 turns, and the secondary coil contains 80 turns. If the primary current is 2.5 amperes, what is the secondary current I2?

A transformer supplies 60 watts of power to a device that is rated at 20 volts. The primary coil is connected to a 120-volt ac source. What is the current I1 in the primary coil?

The voltage and the current in the primary coil of a nonideal transformer are 120 volts and 2.0 amperes. The voltage and the current in the secondary coil are 19.4 volts and 11.8 amperes. What is the efficiency e of the transformer? The efficiency of a transformer is defined as the ratio of the output power to the input power, expressed as a percentage: e=100Pout/Pin.

Solutions

Expert Solution

genius_generous answered 1 year ago
Next > < Previous

Related Solutions

The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives...
The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives readings which are normally distributed with mean μ=115 volts and standard deviation 5 volts. Show that the average of four readings has smaller probability of differing from the true value by 3 volts than an individual reading. Hence show that average of several measurement of the same thing is always more accurate than an individual measurement.
The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives...
The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives readings which are normally distributed with mean μ=115 volts and standard deviation 5 volts. Show that the average of four readings has smaller probability of differing from the true value by 3 volts than an individual reading. Hence show that average of several measurement of the same thing is always more accurate than an individual measurement.
Q 1: If the fluorescence signal from a PMT is 0.531 volts, what will the voltage...
Q 1: If the fluorescence signal from a PMT is 0.531 volts, what will the voltage output be if the following occurs: a. the lamp intensity doubles b. the concentration is reduced by 1/2 c. pathlength is doubled d. the quantum yield drops from 0.50 to 0.10 e.temperature increases Q 2: Predict how the fluorescence signal changes if the following occurs. Explain your answer. [1] the sample temperature decreases [2] the excitation light intensity increases by 25%
An RLC circuit consists of an AC voltage source with a maximum voltage of 122 Volts...
An RLC circuit consists of an AC voltage source with a maximum voltage of 122 Volts connected in series to a resistor, a capacitor, and an inductor. At the resonant frequency, the inductive reactance is 13 Ohms and the total impedance of the circuit is 23 Ohms. What is the average power produced by the battery at 2.6 times the resonant frequency in Watts?
An RLC circuit consists of an AC voltage source with a maximum voltage of 135 Volts...
An RLC circuit consists of an AC voltage source with a maximum voltage of 135 Volts connected in series to a resistor, a capacitor, and an inductor. At the resonant frequency, the inductive reactance is 15 Ohms and the total impedance of the circuit is 24 Ohms. What is the average power produced by the battery at 2.6 times the resonant frequency in Watts?
a) A continuously alternating voltage will produce what type of ultrasound signal from a piezoelectric transducer?...
a) A continuously alternating voltage will produce what type of ultrasound signal from a piezoelectric transducer? Give an equation to describe the output. b) Electrical voltage pulses applied to a piezoelectric transducer will produce what type of signal? Give an equation to describe the output. c) The addition of damping material to a transducer changes what parameters? Which are advantageous and which are disadvantageous? How are the disadvantages accounted for? d) What is the limiting factor for resolution of an...
Explain the purpose of the following: (a) CT (Current transformer), (b) PT/VT (Potential Transformer/Voltage Transformer), (c)...
Explain the purpose of the following: (a) CT (Current transformer), (b) PT/VT (Potential Transformer/Voltage Transformer), (c) Relay, (d) Circuit Breaker.
In a LR circuit, R=10Ωand L=2H. If an alternating voltage of 120V and 60Hz is connected in this circuit, then the value current flowing in it will be?
In a LR circuit, R=10Ωand L=2H. If an alternating voltage of 120V and 60Hz is connected in this circuit, then the value current flowing in it will be?
Describe your design for a transformer that steps up voltage from 120 to 1200 V. (Talk...
Describe your design for a transformer that steps up voltage from 120 to 1200 V. (Talk about the numbers of turns and the material of the core, specifically.) Will the input and output be AC or DC electricity (there is only one right answer for this one unless you get fancy)? Compare the input current to the output current (hint: the output power in the secondary coils should be calculated to be the same (actually slightly less, due to inefficiencies)...
Voltage sags and swells. The power quality of a transformer is measured by the quality of...
Voltage sags and swells. The power quality of a transformer is measured by the quality of the voltage. Two causes of poor power quality are “sags” and “swells.” A sag is an unusual dip and a swell is an unusual increase in the voltage level of a transformer. The power quality of transformers built in Turkey was investigated in Electrical Engineering (Vol. 95, 2013). For a sample of 103 transformers built for heavy industry, the mean number of sags per...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT