Question

In: Electrical Engineering

Source Problem: Design a grounded-load v-I converter that converts a 0V to 10V input to a...

Source Problem:

Design a grounded-load v-I converter that converts a 0V to 10V input to a 4mA to 20mA output. The circuit is to be powered from +/-15V regulated supplies.

My Question:

What does it mean by a grounded-load? I am not really familiar with this term.

Solutions

Expert Solution


Related Solutions

Design a buck-boost converter with a source varying from 10 to 14 V. The output voltage...
Design a buck-boost converter with a source varying from 10 to 14 V. The output voltage is regulated at – 12 V. The load varies from 10 to 15 W. The output voltage ripple must be less than 1 % for any operating condition. a) Determine the range of the duty ratio of the switch. b) Design the inductor and capacitor values used in your design. c) Confirm your solutions using a simulation software for every operating condition (you must...
Design a half wave rectifier where the input source is 220 Vrms, frequency 50Hz, the load...
Design a half wave rectifier where the input source is 220 Vrms, frequency 50Hz, the load is 20Ω. Determine the following , in order to have ∆Vo =1%. Find the equation for the output voltage. Find the Fourier series for the output before adding a capacitor to the circuit. Find the equation for the output current after adding the capacitor. Find the capacitor in order to meet this specification. and this all information for this question
An unbalanced three-phase wye-connected and grounded load is connected to a balanced three-phase four-wire source. The...
An unbalanced three-phase wye-connected and grounded load is connected to a balanced three-phase four-wire source. The load impedances are Za = 14+j3 Ω , Zb = 5-j24Ω and Zc =1+j14 Ω  and the phase a line voltage has an effective value of 18 Kv: use line-to-neutral voltage of phase A as a reference. Find the line and neutral current, also find the reactive power delivered to load and power factor.
Consider an ideal down converter supplying load resistance of 80 ohms from a voltage source rated...
Consider an ideal down converter supplying load resistance of 80 ohms from a voltage source rated 9V and 250mA. The converter operates at 70-kHz and is designed for 5% voltage ripple and 10% current ripple with a duty time of 60%. a) Calculate the output voltage, output voltage ripple, output current and output current ripple. b) Calculate the cycle period, T on and T off. c) Calculate the required inductance and capacitance values d) Calculate the output voltage as functions...
A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty...
A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty ratio d=50%, load resistance RL= 20Ω, inductance 100μH, and capacitance 680 μF. If you were trying to make a boost converter enter DCM, but your load resistor could not reach Rcrit, what other controllable parameters (not including Vin) could you change to reduce the lowest value of i_L to zero? Explain your reasoning.
Problem Definition: You have to design a feedback controller for the Boost Converter that link a...
Problem Definition: You have to design a feedback controller for the Boost Converter that link a voltage source ?? = 80 ± 20% to a load with dc output voltage of 380V. The maximum output current is 2.5A. Questions: 1- Design the Boost converter to satisfy the required output voltage and current. a. Determine the inductance value for continuous conduction mode (CCM). b. Determine a reasonable output voltage ripple and calculate the capacitance accordingly. c. Justify any assumption you made....
Problem: Design and write a C language program that can be used as a unit converter...
Problem: Design and write a C language program that can be used as a unit converter application. Your unit converter should contain at least four unit categories, for example: length, mass, temperature, and time. The program should display the main menu that contains unit categories that are available, and the user will be prompted to select a unit category first. After the unit category has been selected the program should then display another menu (i.e., a submenu) that contains at...
Design a combinational circuit that implements a Binary-to-Grey Code converter. Your input should be a four-bit...
Design a combinational circuit that implements a Binary-to-Grey Code converter. Your input should be a four-bit binary number, and your output should be the equivalent four-bit Grey Code value. First, design the circuit using NAND gates only. Next, design the circuit using a minimal number of 2-input XOR gates.
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty...
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty ratio d= 30%, load resistance R_L= 20Ω, inductance =100 μH, and capacitance= 680 μF. 1) Calculate the following values, and include units in your answers: a) Peak-to-peak current ripple through the inductor, Δ_iL b) Average inductor current that will cause the converter to enter DCM b) Load resistance that will cause the converter to enter DCM (R_crit) d) Average voltage across the inductor insteady-state
a) Design and implement a combinational circuit that converts excess-3 to BCD code using 2-input NAND...
a) Design and implement a combinational circuit that converts excess-3 to BCD code using 2-input NAND gates. (Design: means show all the steps) b) Draw the logic diagram of 2x4 decoder using NOR gates only. Include an enable input. (describe in details) c) Construct a 5-to-32-line decoder with four 3-to-8 decoders with enable and a 2-to-4-line decoder. Use block diagrams for the components. (Describe in details while you are constructing the required circuit) d) Design a 2-bit multiplier using a...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT