Question

In: Mechanical Engineering

low carbon steel having a tensile strength of 350 MPa and shear strength of 250 MPa...

low carbon steel having a tensile strength of 350 MPa and shear strength of 250 MPa is cut in a turning operation with a cutting speed of 200 m/min. The feed is 0.3 mm/rev and the depth of cut is 4.8 mm. The rake angle of the tool is 12 degrees in the direction of chip flow. The resulting chip ratio is 0.8. Using the orthogonal model as an approximation of turning determine...

a.The shear plane angle.

b. Shear force

c. Cutting force

d. Friction force

e. Normal force to shear and coefficient of friction.  

f. Cutting power and cutting horsepower.

Solutions

Expert Solution


Related Solutions

An ASTM A36 steel having a yield strength of 235 MPa, a tensile strength of 640...
An ASTM A36 steel having a yield strength of 235 MPa, a tensile strength of 640 MPa, and an endurance limit of 210 MPa is subjected to a cyclic loading. Using the Goodman diagram, predict whether the material has an infinite fatigue life, or whether it will fail by yielding or fatigue, when the cyclic stress is between: (i) 0 and 250 MPa. (ii) 95 ± 220 MPa
For a brass alloy, the tensile strength is 400 MPa, the yield strength is 315 MPa...
For a brass alloy, the tensile strength is 400 MPa, the yield strength is 315 MPa and the modulus of elasticity is 100 GPa. (a) What is the maximum load that may applied to the specimen with a cross sectional area of 130 mm2 before it fractures? (b) For the same cross sectional area, if the original length of the specimen is 75 mm what will be the length of the specimen, when a load of 13000 N is applied...
The average tensile strength of carbon fiber cloth is 600 MPa. You are testing a new...
The average tensile strength of carbon fiber cloth is 600 MPa. You are testing a new weaving pattern for the carbon fiber threads and want to know if this new weave causes a difference in the tensile strength. After testing 18 samples of the new weave, you found a sample average of 585 MPa with a standard deviation of 34 MPa. At a significance level of 0.05, test to see if this new weave has a different mean than 600...
Consider an orthogonal machining process carried out on a steel alloy of 600 MPa shear strength,...
Consider an orthogonal machining process carried out on a steel alloy of 600 MPa shear strength, the width of the cut is 10mm. The depth of cut is 0.5 mm and the chip thickness 0.7mm. The cutting speed is 2400 m/sec, the coefficient of friction is 0.364 and the rake angle of the tool is 10 oC. Estimate : a) Material removal rate b) specific power in shear c) specific power in friction
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength...
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength is approximately normally distributed with sigma= 60 psi. A random sample of 12 specimens has a mean tensile strength of 3450 psi. a) Compute a two-side confidence interval on the maen tensile strength at a 95% confidence level. b) Test the hypothesis that the mean strength is 3500 psi at alfa=0.05, and provide a conclusion statement. c) If we keep the signifiance level constant...
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength...
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength is approximately normally distributed with σ = 60 psi. A random sample of 12 specimens has a mean tensile strength of 3450 psi. a) Compute a two-sided confidence interval on the mean tensile strength at a 95% confidence level b) Test the hypothesis that the mean strength is 3500 psi at α= 0.05, and provide a conclusion statement
Of the materials shown with a tensile strength of 1000 MPa, the densest ones are high...
Of the materials shown with a tensile strength of 1000 MPa, the densest ones are high carbon steel nickel-based superalloys titanium alloys tungsten alloys
At a tensile strength of 1000 MPa, the material with the lowest embodied energy is titanium...
At a tensile strength of 1000 MPa, the material with the lowest embodied energy is titanium alloys high carbon steel nickel-based superalloys tungsten alloys
1) An engineer who is studying the tensile strength of a steel alloy knows that tensile...
1) An engineer who is studying the tensile strength of a steel alloy knows that tensile strength is approximately normally distributed with σ = 60 psi. A random sample of 12 specimens has a mean tensile strength of 3450 psi. a) Compute a two-sided confidence interval on the mean tensile strength at a 95% confidence level b) Test the hypothesis that the mean strength is 3500 psi at α= 0.05, and provide a conclusion statement c) If we keep the...
2. Consider the following observations on shear strength (MPa) of a joint bonded in a particular...
2. Consider the following observations on shear strength (MPa) of a joint bonded in a particular manner: 22.2 40.4 16.4 73.7 36.6 109.9 30.0 4.4 33.1 66.7 81.5 a. Calculate the value of the sample mean and median. Why is the median so different from the mean? Explain. [3 points] b. Calculate the sample standard deviation. [2 points] c. Are the smallest and largest observations outliers? Justify your answer with appropriate calculations. [5 points] Are the smallest and largest observations...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT