Question

In: Mechanical Engineering

For a brass alloy, the tensile strength is 400 MPa, the yield strength is 315 MPa...

For a brass alloy, the tensile strength is 400 MPa, the yield strength is 315 MPa and the modulus of elasticity is 100 GPa.

(a) What is the maximum load that may applied to the specimen with a cross sectional area of 130 mm2 before it fractures?

(b) For the same cross sectional area, if the original length of the specimen is 75 mm what will be the length of the specimen, when a load of 13000 N is applied in the longitudinal direction?

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

An ASTM A36 steel having a yield strength of 235 MPa, a tensile strength of 640...
An ASTM A36 steel having a yield strength of 235 MPa, a tensile strength of 640 MPa, and an endurance limit of 210 MPa is subjected to a cyclic loading. Using the Goodman diagram, predict whether the material has an infinite fatigue life, or whether it will fail by yielding or fatigue, when the cyclic stress is between: (i) 0 and 250 MPa. (ii) 95 ± 220 MPa
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength...
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength is approximately normally distributed with sigma= 60 psi. A random sample of 12 specimens has a mean tensile strength of 3450 psi. a) Compute a two-side confidence interval on the maen tensile strength at a 95% confidence level. b) Test the hypothesis that the mean strength is 3500 psi at alfa=0.05, and provide a conclusion statement. c) If we keep the signifiance level constant...
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength...
An engineer who is studying the tensile strength of a steel alloy knows that tensile strength is approximately normally distributed with σ = 60 psi. A random sample of 12 specimens has a mean tensile strength of 3450 psi. a) Compute a two-sided confidence interval on the mean tensile strength at a 95% confidence level b) Test the hypothesis that the mean strength is 3500 psi at α= 0.05, and provide a conclusion statement
low carbon steel having a tensile strength of 350 MPa and shear strength of 250 MPa...
low carbon steel having a tensile strength of 350 MPa and shear strength of 250 MPa is cut in a turning operation with a cutting speed of 200 m/min. The feed is 0.3 mm/rev and the depth of cut is 4.8 mm. The rake angle of the tool is 12 degrees in the direction of chip flow. The resulting chip ratio is 0.8. Using the orthogonal model as an approximation of turning determine... a.The shear plane angle. b. Shear force...
1) An engineer who is studying the tensile strength of a steel alloy knows that tensile...
1) An engineer who is studying the tensile strength of a steel alloy knows that tensile strength is approximately normally distributed with σ = 60 psi. A random sample of 12 specimens has a mean tensile strength of 3450 psi. a) Compute a two-sided confidence interval on the mean tensile strength at a 95% confidence level b) Test the hypothesis that the mean strength is 3500 psi at α= 0.05, and provide a conclusion statement c) If we keep the...
Of the materials shown with a tensile strength of 1000 MPa, the densest ones are high...
Of the materials shown with a tensile strength of 1000 MPa, the densest ones are high carbon steel nickel-based superalloys titanium alloys tungsten alloys
At a tensile strength of 1000 MPa, the material with the lowest embodied energy is titanium...
At a tensile strength of 1000 MPa, the material with the lowest embodied energy is titanium alloys high carbon steel nickel-based superalloys tungsten alloys
An engineer who is studying the tensile strength of a steel alloy intended for use in...
An engineer who is studying the tensile strength of a steel alloy intended for use in golf club shafts knows that tensile strength is approximately normally distributed withσ = 70 psi. A random sample of 12 specimens has a mean ten-sile strength of x = 3450 psi. (a) Test the hypothesis that mean strength is 3500 psi. Use α = 0.05. (b) What is the smallest level of significance at which you would be willing to reject the null hypothesis?...
Provide a sketch of how the tensile strength and the hardness of a simple Fe-C alloy...
Provide a sketch of how the tensile strength and the hardness of a simple Fe-C alloy changes as the carbon content is varied. Details the reasons behind the responses that you have sketched – ensuring you relate these to the relevant diagrams.
The average tensile strength of carbon fiber cloth is 600 MPa. You are testing a new...
The average tensile strength of carbon fiber cloth is 600 MPa. You are testing a new weaving pattern for the carbon fiber threads and want to know if this new weave causes a difference in the tensile strength. After testing 18 samples of the new weave, you found a sample average of 585 MPa with a standard deviation of 34 MPa. At a significance level of 0.05, test to see if this new weave has a different mean than 600...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT