Question

In: Mechanical Engineering

A roller bearing has a 22 kN radial load applied. For a life of 18000 hours...

A roller bearing has a 22 kN radial load applied. For a life of 18000 hours at 1200 rev/min, specify the smallest suitable roller bearing to use. Assume a rotating outer ring and provide relevant source information for your selected bearing.

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load....
Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load. shaft rotates 800 rpm and its roller bearing has lh=10000 hours working life.Choose the single row roller bearing .(define the diameter of shaft)(Can you assign it to the table pictures.)
Q1 / An axial load of 75 kN was applied to a steel rod of 3...
Q1 / An axial load of 75 kN was applied to a steel rod of 3 m in length and 0.025 m in diameter. Calculate the change in length (∆L), Poisson’s ratio, percent elongation and percent reduction in   area. Take change in diameter (∆d) = 5.73 x10 mm and E = 200 kN / mm . subject :- strength of material
A 300 kN point load is applied to a soil profile that consists of 7 meters...
A 300 kN point load is applied to a soil profile that consists of 7 meters of sand (γt = 19 kN/m3) above 4 meters of clay (γt = 17.5kN/m3) with the groundwater table at a depth of 5 meters. The clay has an OCR = 1.6, an initial void ratio of 0.86, a Cc=0.64 and a Cr=0.12. The sand has a Cc = 0.35 and an initial void ratio of 0.68. Calculate the overall settlement of the profile due...
Assume the life of a roller bearing follows a Weibull distribution with parameters β=2 and δ=7,500...
Assume the life of a roller bearing follows a Weibull distribution with parameters β=2 and δ=7,500 hours. Determine the probability that the bearing will last at least 8000 hours. Verify your answer using R. Determine the expect value and the variance.
Assume the life of a roller bearing follows a Weibull distribution with parameters β=2 and δ=7,500...
Assume the life of a roller bearing follows a Weibull distribution with parameters β=2 and δ=7,500 hours. Determine the probability that the bearing will last at least 8000 hours. Determine the expect value and the variance.
A centrifugal compressor has 22 radial impellers with an impeller exit radius of r2 = 0.25m....
A centrifugal compressor has 22 radial impellers with an impeller exit radius of r2 = 0.25m. Assuming the mass flow rate through the compressor is mdot = 10kg/s, the shaft speed is omega = 10,000 rpm, and the inlet flow is swirl free, calculate a) the total shaft power Ps in kW b) the total temperature rise (?Tt)in the compressor (assume ? = 1.4 and cp = 1004 J/(kg K))
all journal bearing has a shaft diameter=1.25in and suppports a load of 1200lbf. the bushing is...
all journal bearing has a shaft diameter=1.25in and suppports a load of 1200lbf. the bushing is 1.25-in long and has a bore diameter=1.25in. shfat speed=1500 rev/min. average film temperature=115.4o​F and SAE grade 30 lubricant is used. average clearance =0.001125 in. Find a) magnitud and location of min oil-film thickness b) total lubricant volumetric flow rate c) max oil-folm pressure and its angular location d) power loss
A simply supported reinforced concrete beam with uniformly distributed load of 10 kN/m has a span...
A simply supported reinforced concrete beam with uniformly distributed load of 10 kN/m has a span of 6.0 metres. The beam cross-section is 225 mm breadth by 300 mm depth. Sketch and design the beam. Make necessary and realistic assumptions where applicable
(a) DESCRIBE the reasons why concrete has to be pre-stressed before use as a load-bearing beam....
(a) DESCRIBE the reasons why concrete has to be pre-stressed before use as a load-bearing beam. [3 MARKS] (b) EXPLAIN with DIAGRAMS how pre-stressed concrete is made. [5 MARKS] (c) EXPLAIN why pre-stressed concrete loses its strength when subjected to excessive heat from a fire. [2 MARKS]
5. Estimate the life (in hours) of an 02-series single-row deep-groove ball bearing with a 50-mm...
5. Estimate the life (in hours) of an 02-series single-row deep-groove ball bearing with a 50-mm bore working under the following condition: axial force = 4 kN, radial force = 6 kN, outer ring rotating at 360 rpm, temperature = 50 °C, light impact, reliability = 97%. (6 points)
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT