Question

In: Mechanical Engineering

Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load....

Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load. shaft rotates 800 rpm and its roller bearing has lh=10000 hours working life.Choose the single row roller bearing .(define the diameter of shaft)(Can you assign it to the table pictures.)

Solutions

Expert Solution

Answer :

  • The vaues of radial and thrust factors X and Y are taken from the Sdt catelogue which are (X= 0.56 and Y = 1.4)
  • Bearing no. 6407 (C 55300 N )
  • Dynamic Load C = 55 300 ...........( 52615 N obtained value from calculations replaced with next value from std table C = 55300 N)
  • Shaft diameter (d) = 35 mm

table


Related Solutions

A short reinforced concrete column is subjected to a 1000 kN axial compressive load. The moduli...
A short reinforced concrete column is subjected to a 1000 kN axial compressive load. The moduli of elasticity of plain concrete and steel are 25 GPa and 207 GPa, respectively, and the cross-sectional area of steel is 2% of that of the reinforced concrete. Considering the column as a structural member made of a composite material and subjected to load parallel to the steel rebars, calculate the following: a. the modulus of elasticity of the reinforced concrete b. the load...
A short reinforced concrete column is subjected to a 1000 kN axial compressive load. The moduli...
A short reinforced concrete column is subjected to a 1000 kN axial compressive load. The moduli of elasticity of plain concrete and steel are 25 GPa and 207 GPa, respectively, and the cross-sectional area of steel is 2% of that of the reinforced concrete. Considering the column as a structural member made of a composite material and subjected to load parallel to the steel rebars, calculate the following: a. the modulus of elasticity of the reinforced concrete b. the load...
Impeller : 1) Small radial impeller 2) medium radial impeller 3) Large radial impeller 4) Axial...
Impeller : 1) Small radial impeller 2) medium radial impeller 3) Large radial impeller 4) Axial impeller 5) Turbine propeller Which type of impeller can be used for fluids of high viscosity ?
Q1 / An axial load of 75 kN was applied to a steel rod of 3...
Q1 / An axial load of 75 kN was applied to a steel rod of 3 m in length and 0.025 m in diameter. Calculate the change in length (∆L), Poisson’s ratio, percent elongation and percent reduction in   area. Take change in diameter (∆d) = 5.73 x10 mm and E = 200 kN / mm . subject :- strength of material
What are the possible failures of an insufficient column baseplates subjected to axial load and moment.
What are the possible failures of an insufficient column baseplates subjected to axial load and moment.
. A rectangular steel bar is subjected to a fluctuating load from 30 kN tension to...
. A rectangular steel bar is subjected to a fluctuating load from 30 kN tension to 30 kN compression. The bar is 30 mm wide and 7 mm thick with a hole in the middle that is 4 mm in diameter. Find the fatigue and yield factor of safety if the steel is cold-drawn AISI 1040. If the fatigue factor nf<1 and ny>1 then that means that the system will fail at a finite number of cycles. If that is...
A simply supported flanged beam subjected to a factored load of 60 kN/m (including dead load...
A simply supported flanged beam subjected to a factored load of 60 kN/m (including dead load and live load). The beam has an overall depth of 600 mm including slab thickness of 100 mm. The width of the beam is 230 mm, effective span of the beam is 6.25 m and effective cover to the tension reinforcement is 50 mm. Assume M25 grade concrete and Fe415 steel. Check whether the beam needs to be designed as singly reinforced or doubly...
A roller bearing has a 22 kN radial load applied. For a life of 18000 hours...
A roller bearing has a 22 kN radial load applied. For a life of 18000 hours at 1200 rev/min, specify the smallest suitable roller bearing to use. Assume a rotating outer ring and provide relevant source information for your selected bearing.
A hot-rolled steel bar is subjected to a repeated axial tensile load as shown. The material...
A hot-rolled steel bar is subjected to a repeated axial tensile load as shown. The material has ultimate tensile stress S_ut=1300MPa. The bar has a diameter of 30mm. The notch sensitivity factor, theoretical stress concentration factor, and factor of safety are q=0.52,K_t=2.42 and n=1 respectively. Find the maximum force F that the bar can carry for 10^4 cycles at 90% reliability Figures                                                                10 Points Endurance limit                                                   10 Point Endurance strength                                             10 Points Fatigue stress concentration factor                      5points Determination of force              ...
A 450 mm × 650 mm column supports factored axial load of 2500 kN centered in...
A 450 mm × 650 mm column supports factored axial load of 2500 kN centered in single footing. After assuming the depth and density of soil above footing, assume the required depth of footing [10 marks]. a) Check depth due to two-way shear b) Check depth due to one-way shear action c) Calculate the bending moment and steel reinforcement e) Determine development length of dowels d) Check bearing stress e) Determine development length of dowels
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT