Calculate the length of the wall studs that would need to be cut based on the...

Calculate the length of the wall studs that would need to be cut based on the respective finish floor material & finish ceiling materials listed below. list the answer in feet, inches & fraction of an inch or inches & fraction of a inch.

House #3; the finish floor to ceiling height is 9'-7 3/4"; the finish floor material is 1/4" thick tile with 1/4" thick hardi- backer board under the tile, the finish ceiling has 5/8" type "X" fire rated sheetrock applied to it.

Stud length:_____________________________

Expert Solution

milcah answered 2 years ago

Determine the maximum allowable span of nominal 2x4 wall forms studs carrying a design load...

Determine the maximum allowable span of nominal 2x4 wall forms studs carrying a design load of 1000 psf. Stud spacing is 16” on center. Use the allowable stresses for Douglas Fir from Table 13-8 and 7 day load duration. Assume that studs are continuous over 3 or more spans. Limit deflection to l/360 of span length. Based on the maximum allowable span, check for crushing of studs on double 2x4 wales. Conditions are dry.

How many studs are needed to construct 100 feet of a 2 x 4 stud wall?...

How many studs are needed to construct 100 feet of a 2 x 4 stud wall? The wall has one 8-footwide window, four 4-foot-wide windows, two 36-inch-wide doors, one 30-inch-wide door, four corners, two intersections, and eight hold downs located at corners. The stud spacing is 16 inches on center. Allow for two additional studs for each corner, intersection, or doorway; six additional studs for each window less than 6 feet in length; eight additional studs for each window 6...

Calculate the volume of mortar ( cf) for the following brick wall. A double wythe wall...

Calculate the volume of mortar ( cf) for the following brick wall. A double wythe wall 8-feet high by 14-feet wide having one opening 48-inches by 72-inches and one opening 32 inches by 48 inches. Mortar joints are 0.5-inches and there is 25% mortar waste. The joint thickness between the wythes is 0.5-inch thick and is grouted with mortar. There are 982 total bricks (3.75" x2.25" x8") for both wythes including 3% brick waste.

A plank of length l = 2m is hinged at one end to a wall. The...

A plank of length l = 2m is hinged at one end to a wall. The other end is being (temporarily) supported by a worker who is holding it up with his hand, keeping the plank horizontal. The plank has a mass of 20kg, and there is also a toolbox of mass 5kg sitting on it, 50cm away from the worker (1.5 m away from the wall). (a) Draw a free body diagram and an extended free-body diagram for the...

a. Squares with sides of length x are cut out of each corner of a rectangular...

a. Squares with sides of length x are cut out of each corner of a rectangular piece of cardboard measuring 5 ft by 4 ft. The resulting piece of cardboard is then folded into a box without a lid. Find the volume of the largest box that can be formed in this way. b. Suppose that in part (a) the original piece of cardboard is a square with sides of length s. Find the volume of the largest box that...

A wire of length 30 cm is cut into 2 pieces which are then bent into...

A wire of length 30 cm is cut into 2 pieces which are then bent into the shape of a circle of radius r and an equilateral triangle with side length s. Find the value of r which minimizes the total area enclosed by both shapes

A piece of wire of length 50 is cut, and the resulting two pieces are formed...

A piece of wire of length 50 is cut, and the resulting two pieces are formed to make a circle and a square. Where should the wire be cut to (a) minimize and (b) maximize the combined area of the circle and the square? a) To minimize the combined area, the wire should be cut so that a length of ____ is used for the circle and a length of ____is used for the square. (Round to the nearest thousandth...

Suppose you have a wire of length L. You cut a length x to make a square and use the remaining

Suppose you have a wire of length L. You cut a length x to make a square and use the remaining length L - x to make a circle. Use MuPAD to find the length x that maximizes the sum of the areas enclosed by the square and the circle.

An octagonal wall clock is 15.5 inches wide. Find the length of a side of a...

An octagonal wall clock is 15.5 inches wide. Find the length of a side of a clock.

A flaggpole of mass 5km and length 3.0 m is hinged at a wall and supported...

A flaggpole of mass 5km and length 3.0 m is hinged at a wall and supported by a horizontal position by a cable affected to the flagpole at 2.0 M from the wait. The cable makes an angle of 25 with the horizontal. An iron plate of mass 1.5 kg is hanged at the free end of the flagpole. A. what is the tension in the cable. B. What is the horizontal force excerted on the hinge of the wall....

Question