Question

In: Mechanical Engineering

a) A machined steel has the following properties: Sut= 400 MPa, Sy= 350 MPa, and S’e=...

a) A machined steel has the following properties: Sut= 400 MPa, Sy= 350 MPa, and S’e= 200 MPa. The value f = 0.9 Sketch the S-N diagram for this material, label the key points on the graph and compute the material strength (Sf) corresponding to 800,000 loading cycles?

b) What value of strength of the materials described above should be used if 3,000,000 loading cycles are expected during the life of this part?

Solutions

Expert Solution


Related Solutions

low carbon steel having a tensile strength of 350 MPa and shear strength of 250 MPa...
low carbon steel having a tensile strength of 350 MPa and shear strength of 250 MPa is cut in a turning operation with a cutting speed of 200 m/min. The feed is 0.3 mm/rev and the depth of cut is 4.8 mm. The rake angle of the tool is 12 degrees in the direction of chip flow. The resulting chip ratio is 0.8. Using the orthogonal model as an approximation of turning determine... a.The shear plane angle. b. Shear force...
For a brass alloy, the tensile strength is 400 MPa, the yield strength is 315 MPa...
For a brass alloy, the tensile strength is 400 MPa, the yield strength is 315 MPa and the modulus of elasticity is 100 GPa. (a) What is the maximum load that may applied to the specimen with a cross sectional area of 130 mm2 before it fractures? (b) For the same cross sectional area, if the original length of the specimen is 75 mm what will be the length of the specimen, when a load of 13000 N is applied...
properties of steel sectione
properties of steel sectione
Aluminum oxide (Al2O3) has an elastic modulus of 400 GPa and a KIc of 4 MPa•m1/2...
Aluminum oxide (Al2O3) has an elastic modulus of 400 GPa and a KIc of 4 MPa•m1/2 . A specimen is tested in tension and is found to deform elastically up to the point of fracture at a stress of 450 MPa. (a) Make a diagram of engineering stress-engineering strain to show this behavior. (b) Find the strain at fracture. (b) Estimate the flaw size (a) that caused failure (assume Y = 1). (c) If another specimen of the same size...
Steam at 4 MPa and 350°C is expanded in an adiabatic turbine to 120 kPa. What...
Steam at 4 MPa and 350°C is expanded in an adiabatic turbine to 120 kPa. What is the isentropic efficiency of this turbine if the steam is exhausted as a saturated vapor?
Properties of STEEL In the table below, write down as many properties that you can think...
Properties of STEEL In the table below, write down as many properties that you can think of for “STEEL” as a building material. Do some searching on the internet. See if you can fill the sheet.
An ASTM A36 steel having a yield strength of 235 MPa, a tensile strength of 640...
An ASTM A36 steel having a yield strength of 235 MPa, a tensile strength of 640 MPa, and an endurance limit of 210 MPa is subjected to a cyclic loading. Using the Goodman diagram, predict whether the material has an infinite fatigue life, or whether it will fail by yielding or fatigue, when the cyclic stress is between: (i) 0 and 250 MPa. (ii) 95 ± 220 MPa
A steel tank contains water at ? = 1.00 MPa and ℎ = 3100 kJ/kg. Determine...
A steel tank contains water at ? = 1.00 MPa and ℎ = 3100 kJ/kg. Determine the following: a. State of the water; ie whether the water is compressed water or saturated water or superheated vapour? (Hint: Use Saturated water—Pressure table to compare ℎ at ? = 1.00 MPa) b. Estimate the temperature of the water. (Hint: Use Saturated water—Pressure table or Superheated water, depending on the state you find in a) c. Other properties of water in the tank...
1. Balance Sheet 2015 2016 Accounts Receivable $300 $350 Inventory $200 $400 PP&E $400 $400 Income...
1. Balance Sheet 2015 2016 Accounts Receivable $300 $350 Inventory $200 $400 PP&E $400 $400 Income Statement - 2016 Net Sales $,2000 Gross Profit $1,200 Net Income $500 What is Company X’s inventory turnover ratio for 2016? 1.67 2.00 2.67 6.67 2. Company X purchased goods from Company Y at an initial price of $20,000. Additionally, Company Y gave Company X a trade discount of 10% due to the volume of the order. The goods were shipped f.o.b. shipping point...
Questions relative to thermochem a) I have steam at 400 degrees at 1 MPa flowing in...
Questions relative to thermochem a) I have steam at 400 degrees at 1 MPa flowing in a pipe. How much heat per kilogram would I have to remove to condense it into saturated liquid at 1 MPa? b) I have 10kg of steam with an enthalpy of 2600kj/kg at 500 Kpa, what is the temperature of the steam? How much volume will the steam occupy? I am confused about the steam state in question a), is that supposed to be...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT