Question

In: Mechanical Engineering

Saturated liquid Propane flows in to a valve. It enters at 375 psia, and leaves at 15 psia.

 

Saturated liquid Propane flows in to a valve. It enters at 375 psia, and leaves at 15 psia. Mass flow through the valve is 1.25 lbm/hr. Use EES and ‘Propane’ as your fluid.  This new device replaces the valve with a ‘magic’ isentropic device. Assuming the device operates at steady state, and PE and KE terms are insignificant, calculate how much power could be generated by the device (hp)?

Solutions

Expert Solution


Related Solutions

Using Ees Program (With the Code and Output) Saturated liquid Propane flows in to a valve....
Using Ees Program (With the Code and Output) Saturated liquid Propane flows in to a valve. It enters at 375 psia, and leaves at 15 psia. Mass flow through the valve is 1.25 lbm/hr. Use EES and ‘Propane’ as your fluid to calculate the following: The quality of the Propane exiting the valve Temperature of the Propane exiting the valve (in °F) The change in entropy of the Propane (in Btu/lbm-R) a.__________________ b.____________________ c.____________________
A sweet, water-saturated natural gas enters a compressor at 50 psia and 100F and leaves at...
A sweet, water-saturated natural gas enters a compressor at 50 psia and 100F and leaves at 200 psia and 300F. a. Is there any chance of water condensing in the compressor? If so, how much? Answer in lb H2O/MMscf gas compressed. b. Estimate the mole fraction of water vapor in the gas stream leaving the compressor. c. The natural gas is then cooled to 190 psia and 100F before entering the second stge of compression. Should a vapor-liquid scrubber be...
Saturated propane vapor at 200 psia is fed to a well-insulated heat exchanger at a rate...
Saturated propane vapor at 200 psia is fed to a well-insulated heat exchanger at a rate of 2600 standard cubic feet per hour. The propane leaves the exchanger as a saturated liquid (a liquid at its boiling point) at the same pressure. Cooling water enters the exchanger at 70 oF. Flowing concurrently (in the same direction) with the propane. The temperature difference between the outlet streams (liquid propane and water) is 15 oF. Estimate the required flow rate (lbm/h) of...
Question 3 Steam enters an adiabatic turbine at 800 psia and 900oF and leaves at a...
Question 3 Steam enters an adiabatic turbine at 800 psia and 900oF and leaves at a pressure of 40 psia. Determine the maximum amount of work that can be delivered by this turbine.
refrigarent-134a enters the expansion valve of a refrigeration system at 1MPa as a satuarted liquid and...
refrigarent-134a enters the expansion valve of a refrigeration system at 1MPa as a satuarted liquid and leaves at 100kPa. determine the temperature change across the valve a.0 b.65.74C c.640C d.-26.37C
An expansion valve in a refrigeration cycle throttles R134a from 1.2MPa saturated liquid to 0.32MPa. What...
An expansion valve in a refrigeration cycle throttles R134a from 1.2MPa saturated liquid to 0.32MPa. What is the specific volume at the exit of the expansion valve in unit of m3/kg. Round the result to 4 decimal places.
Liquid enters a valve at Tin and exits at Tout, Pout = 1 atm. Determine Tin...
Liquid enters a valve at Tin and exits at Tout, Pout = 1 atm. Determine Tin and Tout to vaporize 20% of the feed if the liquid is 1/3 benzene and 2/3 toluene.
Liquid water at 15 ℃ is heated by mixing it with saturated steam at the same...
Liquid water at 15 ℃ is heated by mixing it with saturated steam at the same pressure. Liquid water enters a chamber at a rate of 4.3 kg/s and saturated steam enters at a rate of 0.17 kg/s. The mixture leaves the mixing chamber as a saturated liquid at 40℃. If the surroundings are at 15℃, determine (a) the temperature of the saturated steam entering the chamber, (b) the exergy destruction during this mixing process, and (c) the second-law efficiency...
The capacity of a propane vapor-compression refrigeration system is 8 tons. Saturated vapor at 0°F enters...
The capacity of a propane vapor-compression refrigeration system is 8 tons. Saturated vapor at 0°F enters the compressor, and superheated vapor leaves at 120°F, 180 lbf/in.2 Heat transfer from the compressor to its surroundings occurs at a rate of 3.5 Btu per lb of refrigerant passing through the compressor. Liquid refrigerant enters the expansion valve at 85°F, 180 lbf/in.2 The condenser is water-cooled, with water entering at 65°F and leaving at 80°F with a negligible change in pressure. Determine (a)...
Propane burns with 15% excess air. Before the propane-air mixture enters the burner, air preheats from...
Propane burns with 15% excess air. Before the propane-air mixture enters the burner, air preheats from 32 F to 575 F. Determine the requirements of the preheater (BTU / h) if the amount of propane fed to the burner is 1.35x105 SCFH (standard cubic feet per hour) Note: In this case, take standard conditions in the natural gas industry, such as 60 F and 1 atm. Report: a) Flow diagram of the complete process and its table of material balance...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT