Question

In: Mechanical Engineering

A certain engine develops an output torque of 1800 + 200sin2?? Nm, where ? is the...

A certain engine develops an output torque of 1800 + 200sin2?? Nm, where ? is the crank angle measured from some datum. This engine drives a machine which requires a driving torque of 1800 + 300sin?? Nm. The rotating parts have a mass of 100 kg, with a radius of gyration of 0.25 m. The maximum speed of the rotating parts is observed to be 250 rev/min. a) Sketch both the driving and load torque curves on the same axes b) Prove that during 1 cycle, the maximum energy is stored between ? and 5.56 radians c) Determine the maximum energy stored d) Determine the minimum speed of the rotating parts e) Determine the coefficient of fluctuation of speed f) Determine the mean power developed by the engine

Solutions

Expert Solution


Related Solutions

from a certain engine measurements are taken of the torque m in Nm with increasing speed...
from a certain engine measurements are taken of the torque m in Nm with increasing speed (rounds per minute rpm)results are written below. rpm 2000 2500 3000 3500 4000 4500 5000 M. 65 92 139 150 170 175 218 the model parameters for simple transgression in least squares sense are: y intercept = -19.8571 and slope = 0.0469 SSE = 749.71 1. what is the average torque at 3500 rpm? 2. what is the confidence interval for slope beta1 with...
An automotive engine develops maximum torque at a speed of 1000 rpm At this speed, the...
An automotive engine develops maximum torque at a speed of 1000 rpm At this speed, the power developed by the engine is 25 kW. The engine is equipped with a single plate clutch having two pairs of friction surfaces. The mean diameter of the friction disk is 190 mm and the coefficient of friction is 0.35. Six springs, with a spring index of 6, provide the necessary axial force. The springs are made of patented and cold-drawn steel wires of...
I'm running a single cylinder engine simulation using ADAMS/View to determine the torque output based off...
I'm running a single cylinder engine simulation using ADAMS/View to determine the torque output based off of the combustion force which needs to be given as a function of time. I'm having trouble with the setup for the combustion force function setup. Can someone explain how to set up such a function?
Definition of Work, Energy,Power, and Torque In Gasoline Engine
Definition of Work, Energy,Power, and Torque In Gasoline Engine
Calculate the torque M which the engine of the pickup truck must supply to the rear...
Calculate the torque M which the engine of the pickup truck must supply to the rear axle to roll the front wheels over the curbing from a rest position if the rear wheels do not slip. Determine the minimum effective coefficient of friction at the rear wheels to prevent slipping. The mass of the loaded truck with mass center at G is 1900 kg. Calculate the torque M which the engine of the pickup truck must supply to the rear...
) A wet multiple-disc clutch with sintered linings is required to transmit 120 Nm of torque...
) A wet multiple-disc clutch with sintered linings is required to transmit 120 Nm of torque at 1000 rev/min. The axial force is created when 6 helical compression springs deflect 5 mm. Each spring has a spring constant k = 142 N/mm. Assuming uniform wear, determine :- (i) the outside and inside diameters if ri = 0.577 ro . (ii) the number of discs required. (iii) the maximum power that can be transmitted
The torque. T Nm, required to rotate shafts of different diameters, D mm, on a machine...
The torque. T Nm, required to rotate shafts of different diameters, D mm, on a machine has been tested and recorded below. Use the method of least squares to determine the linear regression equation that relates the torque to the diamter. Use 3 decimal places for the figures D (mm) 1 5 11 14 20 24 T (Nm) 1.8 4.2 7.9 9.6 12.9 15.3 ?=___D+ ___Nm
An assembly process includes a torque wrench that automatically tightens engine bolts. The wrench has a...
An assembly process includes a torque wrench that automatically tightens engine bolts. The wrench has a known process standard deviation of 4 foot pounds of torque. A sample of 25 bolts is selected and the average torque to which they have been tightened is 120 foot pounds. What is the 95% confidence interval for the average torque being applied by this wrench?
A multi-disc wet clutch is to transmit 120 Nm of torque at 1000 rpm using sintered...
A multi-disc wet clutch is to transmit 120 Nm of torque at 1000 rpm using sintered friction material. (i) Assuming uniform wear, find the outside and inside diameters required if ri = 0.577ro. (ii) What is the power transmitted? (iii) Using the diameters found in (i), determine the power transmitted when the clutch is new.
A certain medicine was given to a sample of 1800 patients. Of those patients given the...
A certain medicine was given to a sample of 1800 patients. Of those patients given the medicine, 845 had a significant improvement in their health status. Use that information to: a) Determine a 98% confidence interval for p, the population proportion of patients that would be helped by the medicine. b) Determine a 95% confidence interval for p, the population proportion of patients that would be helped by the medicine.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT