Design a common-emitter amplifier that has a dc input value of 15v and that meets the...

Design a common-emitter amplifier that has a dc input value of 15v and that meets the following requirements

1. a gain of at least 80

2. low frequency -3dB less than 100Hz

Expert Solution

Manojponduru answered 1 year ago

write a coclusion for below statement In summary, a typical Emitter Amplifier, the input is connected...

write a coclusion for below statement In summary, a typical Emitter Amplifier, the input is connected to the B-E junction, and the output from the EC terminal is taken. As it provides good current Gain and good voltage gain, it is commonly used as an amplifier circuit and is also known as an inverter amplifier as it gives 180 ° phase shift from input to output. First, when a bypass capacitor is attached, a common-emitter BJT amplifier with a voltage...

Q) a) Explain the effect of bypass capacitor on the common-emitter amplifier? b) Explain the effect...

Q) a) Explain the effect of bypass capacitor on the common-emitter amplifier? b) Explain the effect of swamping on the common-emitter amplifier?

draw appropriate diagrams and explain in detail, why in common emitter amplifier we should have the...

draw appropriate diagrams and explain in detail, why in common emitter amplifier we should have the ac signal between base and emitter to be much less than the thermal voltage

Design a single stage BJT amplifier with the following constraints: This involves the following: -DC and...

Design a single stage BJT amplifier with the following constraints: This involves the following: -DC and AC analysis and the frequency response of the amplifier. -Use a 2N2222 transistor -Power supply (VCC): 6 V -An input impedance near to 3 kΩ -Overall midband voltage gain of -30 V/V -A load resistance of 2 kΩ -The input signal has an RSignal of 500 Ω -Choose a good Qpoint and select the coupling and bypass capacitors to obtain an fL-3dB of 100...

Design a common emitter transistor so that it will operate in the linear region with a...

Design a common emitter transistor so that it will operate in the linear region with a max swing on the output. Use a voltage divider configuration with a collector current of Ic = 2mA and a supply voltage of 12 V.Choose Ve =10% of Vcc. Draw the circuit diagram and calculate all the resistor values

Explain the operation of the isolation amplifier. Design a circuit that takes an input voltage and...

Explain the operation of the isolation amplifier. Design a circuit that takes an input voltage and outputs a scaled differentiated version of the input minus a scaled version of the input, at the output of the circuit

Operational amplifier question Design a non- inverting amplifier with gain of 7.5?

1. the use of Amplifier Loading in a circuit.? 2. the DC operation of a BJT...

1. the use of Amplifier Loading in a circuit.? 2. the DC operation of a BJT using an equivalent model in terms of base current (master) and output current (slave) loops.

Problem Statement: Design a combinational logic circuit that meets the following specifications: • Input: 3-bit binary...

Problem Statement: Design a combinational logic circuit that meets the following specifications: • Input: 3-bit binary integer (A), 2-bit binary integer (B). • Output: 5-bit binary integer (X) = (AxB). For example, A=6, B=2, X=6x2=12. Notation: • A=(A2,A1,A0) • B=(B1,B0) • X=(X4,X3,X2,X1,X0) Required Output: Show the truth table and a minimal logic expression for each of the outputs. Also, draw a logic diagram using discrete gates. Extra Credit: Redesign by using multiplexers and minimal discrete logic as appropriate. 1 |...

The RF amplifier of a receiver has an input resistance of 1 kΩ, and equivalent shot...

The RF amplifier of a receiver has an input resistance of 1 kΩ, and equivalent shot noise resistance of 2 kΩ, a gain of 25, and a load resistance of 125 kΩ. Given that the bandwidth is 1.0 MHz and the temperature is 20 °C. If this receiver is connected to an antenna with an impedance of 75 Ω, calculate the noise figure. (in dB)

Question