Q) a) Explain the effect of bypass capacitor on the common-emitter amplifier? b) Explain the effect...

Q)

a) Explain the effect of bypass capacitor on the common-emitter amplifier?

b) Explain the effect of swamping on the common-emitter amplifier?

Expert Solution

Manojponduru answered 1 year ago

draw appropriate diagrams and explain in detail, why in common emitter amplifier we should have the...

draw appropriate diagrams and explain in detail, why in common emitter amplifier we should have the ac signal between base and emitter to be much less than the thermal voltage

Design a common-emitter amplifier that has a dc input value of 15v and that meets the...

Design a common-emitter amplifier that has a dc input value of 15v and that meets the following requirements 1. a gain of at least 80 2. low frequency -3dB less than 100Hz

write a coclusion for below statement In summary, a typical Emitter Amplifier, the input is connected...

write a coclusion for below statement In summary, a typical Emitter Amplifier, the input is connected to the B-E junction, and the output from the EC terminal is taken. As it provides good current Gain and good voltage gain, it is commonly used as an amplifier circuit and is also known as an inverter amplifier as it gives 180 ° phase shift from input to output. First, when a bypass capacitor is attached, a common-emitter BJT amplifier with a voltage...

Explain the concept of operating point and how it is achieved with a common emitter amp,...

Explain the concept of operating point and how it is achieved with a common emitter amp, common source amp, and the op amp-based amplifiers (differentiator, integrator, inverting, and non-inverting amplifiers). *I understand that the operating point of a transistor can be obtained by using the load line method( IV characteristics) but i don't know how to find the operating point specifically for the common emitter amp , common source amp, and the op amp-based amplifiers

explain in detail that what effect to peak current if the value of capacitor filter is...

explain in detail that what effect to peak current if the value of capacitor filter is increased in the DC power supply circuit.. also explain the effect of value of capacitor filter on the ripples and how will we find that of what value of the capacitor should be used for desired ouput note: DC power supply circuit a circuit composing a transformer, full wave rectifier, capacitor filter,voltage regulator, also give an example

Design a common emitter transistor so that it will operate in the linear region with a...

Design a common emitter transistor so that it will operate in the linear region with a max swing on the output. Use a voltage divider configuration with a collector current of Ic = 2mA and a supply voltage of 12 V.Choose Ve =10% of Vcc. Draw the circuit diagram and calculate all the resistor values

State 1 common vitamin deficiency due to malabsorption after gastric bypass surgery for obesity and explain...

State 1 common vitamin deficiency due to malabsorption after gastric bypass surgery for obesity and explain the reason for the deficiency.

(3)a. Briefly explain the main application of positive feedback system (b) Voltage gain of an amplifier...

(3)a. Briefly explain the main application of positive feedback system (b) Voltage gain of an amplifier without feedback is 60dB. It decreases to 40dB with feedback. Calculate the feedback factor. (c) What is the function of zero crossing detector and its practical applications

Draw the circuit required to obtain the characteristic current voltage curve of the common emitter NPN...

Draw the circuit required to obtain the characteristic current voltage curve of the common emitter NPN silicon transistor. Show how this circuit works. Draw the voltage sources in the circuit, potential disconnectors, current lines, voltage drops measurement devices, circuit elements.

1. Derive expressions for the differential and common mode gains of the amplifier and thence derive...

1. Derive expressions for the differential and common mode gains of the amplifier and thence derive the common mode rejection ratio (CMRR). Explain the design steps necessary to achieve a high CMRR. 2. If the differential gain of the first stage of the amplifier is 100 and the -& resistor values associated with the second stage are R1= 15k, R2= 10.5k, R3= 200k and R4= 101k, calculate the CMRR of the whole system. 3. Explain the operation of a Lock...

Question