A kettle is filled with tap water and placed on a stove. The stove element is...

A kettle is filled with tap water and placed on a stove. The stove element is turned on. Explain why the water starts to boil after a while.

Expert Solution

Water boil due a mode of transfer of heat is called convection.

Explanation-

Convection is mode of transfer of heat from one region to another due to bulk movement of particles of medium under the temperature difference.

when stove is tuned on, heat reach from flame of stove to the container of water due to radiation. Now, heat moves from outer surface of bottom of container to inner side ( water side) due to conduction process.

Since, bottom of container has the higher temperature to top surface. So, bottom part of water gains heat due to which its density decreases slighly comparision to the upper part of the water, because of which, these two parts of water ( upper and top) gain some movement. Since, any material moves from higher density to lower density under the gravity. By this way, upper part of water ( which has higher density comparision to lower) moves downward and bottom part of water moves upward taking the heat energy with themselves.

Thus, a cycle forms. Bottom part moves upward taking the heat energy and top part moves downward. This process continues further. By this way, water boil when stove is turned on.

genius_generous answered 1 year ago

A partially filled (plastic) kettle is used to boil water. The kettle contains tap (temperature) water...

A partially filled (plastic) kettle is used to boil water. The kettle contains tap (temperature) water before it is switched on. If the thermostat to switch off the kettle when it boils is faulty: Q2d: Explain the solution strategy which would allow you to calculate the time needed to bring water to the boil. Q2a: Detail all the assumptions needed to arrive at the solution, whether they relate to equations used (i.e., the theoretical basis) or any values which must...

The burner on an electric stove has a power output of 2.0 kW. A 610 g stainless steel tea kettle is filled with 20℃ water and placed on the already hot burner.

The burner on an electric stove has a power output of 2.0 kW. A 610 g stainless steel tea kettle is filled with 20℃ water and placed on the already hot burner. Part A If it takes 3.0 min for the water to reach a boil, what volume of water, in cm3, was in the kettle? Stainless steel is mostly iron, so you can assume its specific heat is that of iron. Express your answer using two significant figures.

You have placed a copper pot with water to heat on the stove. After one minute...

You have placed a copper pot with water to heat on the stove. After one minute you place your finger in the water and you are okay. When you touch the pot your finger gets burned. Upload a drawing of a molecular view of what the copper atoms and water molecules look like at the beginning of heating the pot and after the pot has been heated for 15 mins.

The heater element of a kettle has a constant resistance of 105ohm and apllied voltage of...

The heater element of a kettle has a constant resistance of 105ohm and apllied voltage of 240V Calculate the time taken to raise the temperature of on litre of water from 15degrees celsius to 90 degrees celsius assuming that only 80% of the power input to the kettle is usefully employed If the water equivalent of the kettle is 150g, find out how long it will take tobraise a second litre of water through the same temperature range immediately after...

Does tap water conduct electricity? Explain.

Water heater In a water heater, tap water with the temperature 10 degrees celcius is heated...

Water heater In a water heater, tap water with the temperature 10 degrees celcius is heated to 60 degrees celcius. For a shower, a total of 20 litres of water is used. Water from the water heater is mixed with tap water to reach the temperature 35 degrees celcius when one showers. How much ENERGY is needed to heat 10 litres of water from 10 celcius to 60 celcius? How much EXERGY is needed to heat 10 litres of water...

As the heating element on a stove top gets hotter, it begins to glow at visible...

As the heating element on a stove top gets hotter, it begins to glow at visible wavelengths. a) What temperature must the heating element achieve to glow most brightly at red wavelengths of 700 nm? b) What temperature must the heating element achieve to glow most brightly at blue wavelengths of 450 nm? c) Typically, home appliances are color coded such that red represents hot settings and blue represents cold settings. Why might this color coding seem backwards to a...

Compare the water quality of the natural water sample and tap water analyzed. Which quality parameters...

Compare the water quality of the natural water sample and tap water analyzed. Which quality parameters of natural water are significantly different from tap water? What quality parameters you measured in this lab are regulated by the National Primary Drinking Water Standards? Is the quality of the tap water in compliance with these standards? 3. (5107 only, bonus for 4107) Compare the results of sulfate measu

Microplastics have been found in both tap water and bottled water. Bottled water results A study...

Microplastics have been found in both tap water and bottled water. Bottled water results A study analyzed 259 bottles and found an average of 320 plastic particles for every liter of water being sold. The associated standard deviation was 327. (Yes, the standard deviation is larger than the mean.) Tap water results In a similar study, 30 tap water samples were analyzed. The average number of plastic particles found in each liter in the United States was 8.8 with a...

1. In a colorimetry, why is refrigerated water is better than tap water? 2. "The heat...

1. In a colorimetry, why is refrigerated water is better than tap water? 2. "The heat transfer of thermal energy to matter usually leads to an increase in temperature". Why not 'always' rather than 'usually'? 3. Several objects lying side by side on a table will not feel equally cool to touch even though they are at the same temperature. Explain.

Question