Question

In: Mechanical Engineering

A Magnesium Alloy bar 6 in. in diameter is being turned on a lathe at a...

A Magnesium Alloy bar 6 in. in diameter is being turned on a lathe at a depth of cut d = 0.050 in. The lathe is equipped with a 10-hp electric motor and has a mechanical efficiency of 80%. The spindle speed is 500 rpm. Estimate the maximum feed that can be used before the lathe begins to stall.

   

(0.45 W-s/mm^3 value of specific power for magnesium alloy)

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

6) A tapered surface is to be turned on an automatic lathe. The work piece is...
6) A tapered surface is to be turned on an automatic lathe. The work piece is 900 mm long with minimum and maximum diameters of 150 mm and 300 mm at opposite ends. The automatic controls on the lathe permit the surface speed to be maintained at a constant value of 200 m/min by adjusting the rotational speed as a function of work piece diameter. Feed=0.25 mm/rev and depth of cut = 3.5 mm. The rough geometry of the piece...
An alloy of magnesium and lead is 50% lead by weight. A) convert this alloy to...
An alloy of magnesium and lead is 50% lead by weight. A) convert this alloy to an equivalent atomic percentage. B) Convert this alloy to an equivalent volume percentage
Discuss the likely form of a magnesium/lead alloy that doesnt form an intermetallic when magnesium is...
Discuss the likely form of a magnesium/lead alloy that doesnt form an intermetallic when magnesium is present at low concentration. Use any relevant information to support your arguments.
a tapered surface is to be turned on an automatic lathe the work piece is 750...
a tapered surface is to be turned on an automatic lathe the work piece is 750 mm long with minimum and maximum diameter of 100 & 200 mm at opposite ends the automatic controls on the lathe permit to surface speed to be maintained at a constant value of 200 m/min by adj Listing the rotational speed as a function of workpiece diameter. Feed = 0. 25 mm/rev and depth of cut · 3. 0 m. The rough geometry of...
A lathe is set to cut bars of steel into lengths of 6 centimeters. The lathe...
A lathe is set to cut bars of steel into lengths of 6 centimeters. The lathe is considered to be in perfect adjustment if the average length of the bars it cuts is 6 centimeters. A sample of 121 bars is selected randomly and measured. It is determined that the average length of the bars in the sample is 6.08 centimeters with a standard deviation of 0.44 centimeters. The hypotheses to determine whether or not the lathe is in perfect...
The diameter of alloy rods produced on an extrusion machine are known to have a standard...
The diameter of alloy rods produced on an extrusion machine are known to have a standard deviation of 0.0001 inches. A random sample of 25 rods have a mean diameter of 0.5046 inches. a) Test the hypothesis that the mean diameter is 0.5025 inches. Assume a 2-sided alternative and use α=.05. Be sure to identify the decision rule, the critical values. Draw pictures to visualize. b) Construct the 2-sided 95% confidence interval for this test with α=.05. c) What is...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the liberated H2(g) is collected over water at 29 ∘C and 752 torr, the volume is found to be 303 mL . The vapor pressure of water at 29 ∘C is 30.0 torr. How many moles of H2 can be produced from x grams of Mg in magnesium-aluminum alloy? The molar mass ofMg is 24.31 g/mol. Express your answer in terms of x to four...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the liberated H2(g) is collected over water at 29 ∘C and 752 torr, the volume is found to be 305 mL . The vapor pressure of water at 29 ∘C is 30.0 torr. a. Taking into account the vapor pressure of water, how many moles of hydrogen gas, n, are present in 305 mL at 752 torr and 29 ∘C? The value of the gas...
A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A...
A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A force of 9070 N produces an elastic reduction in specimen diameter of 0.0048 mm. Calculate the elastic modulus (in GPa) of this material if its Poisson's ratio is 0.33.
The cable lifting an elevator is wrapped around a 1.2-m-diameter cylinder that is turned by the...
The cable lifting an elevator is wrapped around a 1.2-m-diameter cylinder that is turned by the elevator's motor. The elevator is moving upward at a speed of 1.3 m/s . It then slows to a stop, while the cylinder turns one complete revolution. How long does it take for the elevator to stop?
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT