Question

In: Mechanical Engineering

An alloy of magnesium and lead is 50% lead by weight. A) convert this alloy to...

An alloy of magnesium and lead is 50% lead by weight. A) convert this alloy to an equivalent atomic percentage. B) Convert this alloy to an equivalent volume percentage

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

Discuss the likely form of a magnesium/lead alloy that doesnt form an intermetallic when magnesium is...
Discuss the likely form of a magnesium/lead alloy that doesnt form an intermetallic when magnesium is present at low concentration. Use any relevant information to support your arguments.
A Magnesium Alloy bar 6 in. in diameter is being turned on a lathe at a...
A Magnesium Alloy bar 6 in. in diameter is being turned on a lathe at a depth of cut d = 0.050 in. The lathe is equipped with a 10-hp electric motor and has a mechanical efficiency of 80%. The spindle speed is 500 rpm. Estimate the maximum feed that can be used before the lathe begins to stall.     (0.45 W-s/mm^3 value of specific power for magnesium alloy)
An alloy is composed of elements A (78%) and B (12%) by weight. The density of...
An alloy is composed of elements A (78%) and B (12%) by weight. The density of the alloy is 1.95 g/cm3. The properties of these elements are shown below: Element Gram Atomic Weight σa (barns) σs (barns) A 22.1999 0.19 1.38 B 25.0055 0.21 2.44 Determine: The atom densities for the two elements. The atomic density for element A:               b. The absorption and scattering macroscopic cross sections for thermal neutrons.               c. The mean free paths for absorption and...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the liberated H2(g) is collected over water at 29 ∘C and 752 torr, the volume is found to be 303 mL . The vapor pressure of water at 29 ∘C is 30.0 torr. How many moles of H2 can be produced from x grams of Mg in magnesium-aluminum alloy? The molar mass ofMg is 24.31 g/mol. Express your answer in terms of x to four...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the...
A 0.250-g sample of a magnesium-aluminum alloy dissolves completely in an excess of HCl(aq). When the liberated H2(g) is collected over water at 29 ∘C and 752 torr, the volume is found to be 305 mL . The vapor pressure of water at 29 ∘C is 30.0 torr. a. Taking into account the vapor pressure of water, how many moles of hydrogen gas, n, are present in 305 mL at 752 torr and 29 ∘C? The value of the gas...
How much copper, in weight percent, is in an alloy consisting of 94.1 at.% Ag and...
How much copper, in weight percent, is in an alloy consisting of 94.1 at.% Ag and 5.9 at.% copper? The atomic weights for Ag and Cu are 107.87 g/mol and 63.55 g/mol, respectively.
Using the given lead-tin phase diagram for an alloy content of 80 wt % Sn and...
Using the given lead-tin phase diagram for an alloy content of 80 wt % Sn and a temperature of 100 C (a) what is the primary phase (b) what are the mass fractions of eutectic and primary phases? Show tie line used and all calculations. Use standard lead-tin phase diagram.
For an alloy that consists of 74.9 g copper, 108.0 g zinc, and 7.3 g lead,...
For an alloy that consists of 74.9 g copper, 108.0 g zinc, and 7.3 g lead, what are the concentrations of (a) Cu, (b) Zn, and (c) Pb in weight percent? The atomic weights of Cu, Zn, and Pb are 63.54, 65.39, and 207.2 g/mol, respectively.
Traditional solder is a low melting point alloy of lead and tin. (Some countries havemandated the...
Traditional solder is a low melting point alloy of lead and tin. (Some countries havemandated the future use of lead-free solders, because of concerns relating to theenvironmental consequences of lead use and disposal.) Using appropriate data gleaned from the textbook, explain (i)  why lead has very limited solubility in solid tin (hardly any lead will dissolve in tin at room temperature); (ii) why tin is moderately soluble in solid lead (approximately 3.5% of the atoms in lead can be replaced by...
An article reports that in a sample of 50 microdrills drilling a low-carbon alloy steel, the...
An article reports that in a sample of 50 microdrills drilling a low-carbon alloy steel, the average lifetime (expressed as the number of holes drilled before failure) was 12.68 with a standard deviation of 6.83. Based on this data, an engineer reported a confidence interval of (11.35, 14.01) but neglected to specify the level. What is the level of this confidence interval? Give your final answer to the nearest percent.                 The level is ____%.
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT