Question

In: Other

1. Three tanks are interconnected non-interactively. The fluid enters the first tank at the flow rate...

1. Three tanks are interconnected non-interactively. The fluid enters the first tank at the flow rate q and the third
leaves the tank at flow rate q3. The speed of the fluid coming out of the third tank is fixed by means of a pump.
It is maintained. According to this,
a) Mathematically the effect of the change in the velocity of the fluid entering the first tank on the liquid height in the third tank
Please express. (The areas of the tanks are equal to each other.)
b) If the velocity of the fluid entering the first tank is suddenly increased by 10 units, the height of the liquid in the third tank over time
express the change mathematically. (The time constant of the first and second tanks are 2 minutes and 3 minutes respectively,
area of ​​tanks 1 m2
'D.)
* Show the system schematically

Solutions

Expert Solution

Hope this will be helpful

Please try to follow step by step substitution.

Page 1

Page 2

Page 3

Page 4

Give your feedback


Related Solutions

Consider two interconnected tanks. Tank 1 initial contains 40 L (liters) of water and 160 g...
Consider two interconnected tanks. Tank 1 initial contains 40 L (liters) of water and 160 g of salt, while tank 2 initially contains 20 L of water and 250 g of salt. Water containing 20 g/L of salt is poured into tank1 at a rate of 2 L/min while the mixture flowing into tank 2 contains a salt concentration of 35 g/L of salt and is flowing at the rate of 2.5 L/min. The two connecting tubes have a flow...
Fluid enters a tube with a flow rate of 0.021 kg/s and an inlet temperature of...
Fluid enters a tube with a flow rate of 0.021 kg/s and an inlet temperature of 20°C. The tube, which has a length of 6.280 m and diameter of 15 mm, has a surface temperature of 30°C. Determine the heat transfer rate to the fluid if it is water. The heat transfer rate to the fluid, in W is?
A tank contains 100 gal of water. Brine enters the tank at the rate of 3...
A tank contains 100 gal of water. Brine enters the tank at the rate of 3 gal/min. The mixture, thoroughly stirred, leaves the tank at the rate of 2 gal/min. If the salt concentration in the brine at the end of 20 minutes is to be 2 lb/gal, what should be the salt concentration in the brine entering the tank?
A tank contains 100 gal of water. Brine enters the tank at the rate of 3...
A tank contains 100 gal of water. Brine enters the tank at the rate of 3 gal/min. The mixture, thoroughly stirred, leaves the tank at the rate of 2 gal/min. If the salt concentration in the brine at the end of 20 minutes is to be 2 lb/gal, what should be the salt concentration in the brine entering the tank?
Consider three 0.03 m^3 tanks filled with N2, Air and He (tank A, B and C...
Consider three 0.03 m^3 tanks filled with N2, Air and He (tank A, B and C respectively). Each tank is filled with a pressure of 400 kPa at room temperature, 298 K. Determine the mass of gas contained in each tank. Also determine the number of moles of gas in each tank.
A water treatment plant has three identical horizontal shaft flocculation tanks. Each tank is composed of...
A water treatment plant has three identical horizontal shaft flocculation tanks. Each tank is composed of three stages with size of 4 m depth, 14.1 m length and 15 m width. G value of each stage is 40 s-1, 30 s-1 and 20 s-1. Mean water temperature is 15°C (μ = 1.139×10-3). What are the power requirements for flocculation stages in a single flocculation tank. And Is the flocculation tank in an efficient way? ( Plant's average flow rate of...
Design a set of activated sludge aeration tanks. The flow rate to treat is 5.6 MGD...
Design a set of activated sludge aeration tanks. The flow rate to treat is 5.6 MGD and the BOD concentration is 150 mg/L. The design solids concentration (X) at steady-state is 2,000 mg/l. The design MCRT is 7 days. The kinetic coefficients are as follows: K = 2 g BODg cells⋅d, Ks = 25 BOD/L, Kd = 0.06 day-1, Y = 0.5 g BODg cells⋅d. The influent ammonia concentration is 40 mg/l and nitrification is needed. It takes 1400 ft3of...
A reheat Rankine cycle operates with water as the working fluid. Steam enters the first turbine...
A reheat Rankine cycle operates with water as the working fluid. Steam enters the first turbine at 8 MPa and 450◦C and exits at 0.8 MPa. It is then reheated at 400◦C before entering the second turbine, where it exits at 10 kPa. If the amount of work into the pump is 8.04 kJ/kg and the net work per cycle produced is 1410.5 kJ/kg, determine the thermal efficiency. Assume no pressure losses in the condenser or the boiler.
Nitrogen (N2), at 300 K, 1 bar with a mass flow rate of 1 kg/s enters...
Nitrogen (N2), at 300 K, 1 bar with a mass flow rate of 1 kg/s enters an insulated mixing chamber and mixes with carbon dioxide (CO2) entering as a separate stream at 500 K, 1 bar with a mass flow rate of 0.5 kg/s. The mixture exits at 1 bar. Assuming ideal gas behavior, for steady-state operation, determine (a) the molar analysis (i.e., the molar flow rate for each gas) of the exiting mixture, (b) the exit mixture temperature, and...
2. Calculate the volume and dimensions of a rectangular sedimentation tank for a flow rate of...
2. Calculate the volume and dimensions of a rectangular sedimentation tank for a flow rate of 10,000 gpm based on a maximum overflow rate of 650 gallons per day/sq ft. Also, determine the length of the effluent weir and calculate the horizontal flow velocity in the tank.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT