Question

In: Civil Engineering

2. Calculate the volume and dimensions of a rectangular sedimentation tank for a flow rate of...

2. Calculate the volume and dimensions of a rectangular sedimentation tank for a flow rate of 10,000 gpm based on a maximum overflow rate of 650 gallons per day/sq ft. Also, determine the length of the effluent weir and calculate the horizontal flow velocity in the tank.

Solutions

Expert Solution


Related Solutions

How can I design a rectangular sedimentation tank? Inputs: Average Flowrate , Peak Flowrate ,Number of...
How can I design a rectangular sedimentation tank? Inputs: Average Flowrate , Peak Flowrate ,Number of tanks, W:L ratio , Launder width, Sidewall depth ,Bottom slope, MLSS concentration ,Recycle ratio (R) Outputs: Length , Width ,Surface loading (for Qave and Qpeak) ,Weir type (one-sided, two-sided, 1/3 of length, corrugated) Weir loading (for Qave and Qpeak) ,Solids loading (for Qave and Qpeak) ,Retention time (for Qave and Qpeak) ,Horizontal velocity (for Qave and Qpeak) (if it is rectangular)
a rectangular open tank is to have a square base, and its volume is to be...
a rectangular open tank is to have a square base, and its volume is to be 125 cubic metrrs. the cost per square meter for the bottom is $24 and for the sides is $12. find the dimensions of the tank for which the cost of the material is to be the least. what is the least cost?
Find the dimensions (in inches) of the rectangular package of maximum volume subject to the constraint...
Find the dimensions (in inches) of the rectangular package of maximum volume subject to the constraint that the sum of the length and the girth cannot exceed 192 inches (see figure). (Hint: Maximize V = xyz subject to the constraint x + 2y + 2z = 192.)
Determine the dimensions of a rectangular solid (with a square base) of maximum volume if its...
Determine the dimensions of a rectangular solid (with a square base) of maximum volume if its surface area is 216 square inches
What are the dimensions for the cheapest possible rectangular box with a volume of 72 cm3  ...
What are the dimensions for the cheapest possible rectangular box with a volume of 72 cm3  if the material for the bottom costs $16/cm2, material for the sides costs $2/cm2, and material for the top costs $20/cm2 ?
A rectangular tank with a square​ base, an open​ top, and a volume of 1372 ft...
A rectangular tank with a square​ base, an open​ top, and a volume of 1372 ft cubed is to be constructed of sheet steel. Find the dimensions of the tank that has the minimum surface area.
consider the following information for a rectangular primary clarifier a)determine the required surface area(m^2),tank volume(m^3) and...
consider the following information for a rectangular primary clarifier a)determine the required surface area(m^2),tank volume(m^3) and detention time (hrs) under both the average flow conditions and peak flow conditions b) calculate and compare the scour velocity (m/s) and peak flow horizontal velocity (m/s) Based on these two values,do you expect the particles to re-suspend during the clarification process. No of rectangular clarifiers=2 Qaverage=20,000m^3/d Qpeak=50,000m^3/d channel width =6m side water depth=4m overflow rate at average flow=40m^3/m^2.d density of water=1000kh/m^3 density of...
IV. Continuity The mass flow rate and the volume flow rate are always the same in...
IV. Continuity The mass flow rate and the volume flow rate are always the same in a closed pipe. Why do you think that has to be the case? (Try and think about what might happen if the rates were not the same).
A mass balance is performed for a treatment process consisting of a sedimentation tank followed by...
A mass balance is performed for a treatment process consisting of a sedimentation tank followed by a mixing tank. First, 25097 m3/d of raw wastewater with solids concentration of 180 mg/l flows into the sedimentation tank. 97% of the incoming solids end up in the sludge. The effluent flows at a rate of 1040 m3/hr. Next, the effluent of the sedimentation tank enters the mixing tank where it is mixed with pure filtered water. Assume that the density is the...
Calculate the flow depth in a rectangular riveted steel open channel with a width of 6.1...
Calculate the flow depth in a rectangular riveted steel open channel with a width of 6.1 m and a slope of 0.0001, since the water flow is 6.8 m3/s.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT