A graduated cylinder filled with water rests upside down in a container of water at 0...

A graduated cylinder filled with water rests upside down in a container of water at 0 C. The water is 7.00 cm deep. Attached to the base of the cylinder is a small ring (but since the cylinder is upside down, the ring is at the highest elevation, available for grabbing). The base of the cylinder has mass 10.0 grams with ring included. The cylinder itself has radius 3.00 cm, height 40.0 cm, and mass 100.0 grams (including the base and ring). Bridgette has a scale that can read hanging weight (but, as so often happens, reads in grams instead of Newtons). She hooks the scale to the ring on the bottom of the cylinder and lifts, so that the base of the cylinder lifts 5.00 cm, but the other end of the cylinder remains beneath the surface of the water. She is amazed that the cylinder remains full of water, seemingly all the way to the base. What is the reading on the scale? (The mass density of the cylindrical part of the graduated cylinder is 1.00 grams per cm3.)

Solutions

Expert Solution

genius_generous answered 1 year ago

Next > < Previous

Related Solutions

3. A graduated cylinder is filled with 50 mL of water . An aluminum cylinder is...

3. A graduated cylinder is filled with 50 mL of water . An aluminum cylinder is dropped , the water rises to 58 mL . As you also add a copper cylinder , the water rises to 64 mL . If the mass of the copper cylinder is 40 grams , find the density of the copper cylinder in g/mL. a) 5 g/mL b) 6.7 g/mL c) 2.9 g/mL d) 40 g/mL 3. A graduated cylinder is filled with 50...

Heat of Vaporization Questions We did a lab where we placed a graduated cylinder upside down...

Heat of Vaporization Questions We did a lab where we placed a graduated cylinder upside down in a beaker to observe the air bubble and how it was affected by temperature. There are a few questions I need help with: 1. You have assumed the vapor pressure of water below 5 degrees Celsius to be negligible. How would the inclusion of its actual vapor pressure affect your results? 2. Assume the graph of ln(P) versus 1/T results in a curved...

A 3.24 g object is immersed into a graduated cylinder filled with water. Use the following...

A 3.24 g object is immersed into a graduated cylinder filled with water. Use the following figure to determine the object’s density. Enter just the numerical value without units. (V1=65ml, V2=90ml) How many grams of water are contained in a 0.127 L sample at 20°C? How much will you spend in fuel to travel 405 miles? Your car gets on average 37 miles per gallon and gas costs $2.70/gallon. Report your answer to four significant figures. Enter just the numerical...

3) A polystyrene container is filled to the brim with water at 0 0C and sealed...

3) A polystyrene container is filled to the brim with water at 0 0C and sealed with a polystyrene lid of the same thickness as the container. The sealed container is immersed in a reservoir of liquid Nitrogen at a temperature of 73 K. The surface area of the container is 5 x 10-2 m2 and the rate of heat flow from the inside to the outside of the container is 66 Watts. (a) Assuming the temperature of inner and...

A stainless steel sphere drops through a graduated cylinder filled .245 meters high with water knowing...

A stainless steel sphere drops through a graduated cylinder filled .245 meters high with water knowing that the mass of the ball is 028236 kg, it took .175 seconds to reach the bottom, and its radius is 0.00955 meters Find the drag force acting

A graduated cylinder is filled to the 40.00−mL mark with a mineral oil. The masses of...

A graduated cylinder is filled to the 40.00−mL mark with a mineral oil. The masses of the cylinder before and after the addition of the mineral oil are 124.966 g and 159.446 g, respectively. In a separate experiment, a metal ball bearing of mass 21.867 g is placed in the cylinder and the cylinder is again filled to the 40.00−mL mark with the mineral oil. The combined mass of the ball bearing and mineral oil is 50.952 g. Calculate the...

A graduated cylinder is filled to the 40.00−mL mark with a mineral oil. The masses of...

PART A A cylinder, with a piston pressing down with a constant pressure, is filled with...

PART A A cylinder, with a piston pressing down with a constant pressure, is filled with 1.90 moles of a gas (n1), and its volume is 40.0 L (V1). If 0.600 mole of gas leak out, and the pressure and temperature remain the same, what is the final volume of the gas inside the cylinder? Express your answer with the appropriate units. PART B A sample of gas in a cylinder as in the example in Part A has an...

Bolt: Mass of bolt _8_g Volume of water in graduated cylinder 10__mL Volume of water and...

Bolt: Mass of bolt _8___g Volume of water in graduated cylinder __10__mL Volume of water and bolt in graduated cylinder _13___mL Volume of bolt (subtract the two volumes) _2__mL Density of the bolt _2.67___ g/mL How to calculated the Archimedes’ Method Bolt: Mass of bolt ____g Mass of Displaced Water ____g Calculated Volume of Displaced Water ____mL Density of the bolt ____ g/mL Magnet: Mass of magnet ____g Mass of Displaced Water ____g Calculated Volume of Displaced Water ____mL Density...

Two Film Cannisters are filled with water. These will be used in Calorimeter. One container will...

Two Film Cannisters are filled with water. These will be used in Calorimeter. One container will be used for heated pennies and the other for heated nickels. The pennies and nickels will be heated to a temp of 66 C. The cannister that will have pennies dropped into it, has a temperature of 20.1 C and a mass of 15.57g. The cannister that will have nickels dropped into it, has a temperature of 19.7 C and a mass of 17,33g....

Subjects