A cylindrical glass tank with a diameter of 8.6 cm and a height of 25 cm...

A cylindrical glass tank with a diameter of 8.6 cm and a height of 25 cm is inverted and inserted into another tank of water. If no air is allowed to escape from the glass container when submerged, what is the height of the air column in the glass tank when its edge is 2.0 m below the surface of the water?

Expert Solution

genius_generous answered 2 years ago

A cylindrical soil sample, 7.3 cm in diameter and 16.8 cm in height, is tested in...

A cylindrical soil sample, 7.3 cm in diameter and 16.8 cm in height, is tested in a constant-head permeability apparatus. A constant head of 75 cm is maintained during the test. After 1 minute of testing, a total of 945.7 gm of water was collected. The temperature was 20 oC. The void ratio of the soil was 0.43. Calculate the following: The hydraulic gradient The flow rate The discharge velocity The seepage force per unit volume The coefficient of permeability

A cylindrical air tank has dimensions diameter = 0.2m and height 0.8m. an attached pressure gage...

A cylindrical air tank has dimensions diameter = 0.2m and height 0.8m. an attached pressure gage reads 200 kPa and the temperature is 27 celcius. an electrical heater is energized inside and it raises the temperature to 147 celius in 2 minutes. Calculate the mass of air in the tank (kg) (have to use ideal gas law, molecular weight of air)

A disk is cast in an open mould with diameter 25 cm and height 15 mm....

A disk is cast in an open mould with diameter 25 cm and height 15 mm. The pouring temperature is 1200°C. Calculate the total heat evolved during cooling if the disk was cast in copper, and given that the heat of fusion is 200 kJ/kg.

A toroid with inner diameter of 3 cm, outer diameter of 5 cm, and height of...

A toroid with inner diameter of 3 cm, outer diameter of 5 cm, and height of 0.1 cm is made of a body-centered-cubic (bcc) paramagnetic material with lattice parameter equal to 0.5 nm. The toroid is wrapped by a copper wire in 20 turns. If each atom of the magnetic material has a magnetic moment of 1.5µB (Bohr Magneton), (a) (1.5 pt) What is the saturation magnetization (in A/m) of the material? (b) (1.5 pt) If a current of 2...

A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A...

A cylindrical specimen of some metal alloy 8.6 mm in diameter is stressed in tension. A force of 9070 N produces an elastic reduction in specimen diameter of 0.0048 mm. Calculate the elastic modulus (in GPa) of this material if its Poisson's ratio is 0.33.

A cylindrical shaped potato with length 2 cm and a diameter of 0.5 cm was dried...

A cylindrical shaped potato with length 2 cm and a diameter of 0.5 cm was dried at a temperature of 65 o C in a convective oven for 24 h, if the surface temperature of the potato remained at 62 o C throughout the drying operation, describe the different changes that occurs during the constant and falling rate periods

Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm...

Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm is subjected to turning using a high speed steel tool. For this tool, n and C values in the Taylor tool life equation are 0.125 and 70 m/min, respectively. The cost for hiring an operator and using the machine tool are $82 per hour. The tooling cost per edge of cutting is $5. Loading and unloading the part on to the machine takes about...

A cylindrical glass beaker of height 1.272 m rests on a table. The bottom half of...

A cylindrical glass beaker of height 1.272 m rests on a table. The bottom half of the beaker is filled with a gas, and the top half is filled with liquid mercury that is exposed to the atmosphere. The gas and mercury do not mix because they are separated by a frictionless, movable piston of negligible mass and thickness. The initial temperature is 276 K. The temperature is increased until a value is reached when one-half of the mercury has...

A cylindrical tank with inner diameter 2.0 m is designed to operate as a fluidized bed...

A cylindrical tank with inner diameter 2.0 m is designed to operate as a fluidized bed reactor for a heterogeneous catalytic reaction. The tank is loaded with a random packing of cubic particles to a height of 4.0 m with voidage 0.4 before the fluidization process. The density and length of each side of the cubic particles are 2600 kg m-3 and 1.0 cm respectively. During operation, a liquid reactant with density 1000 kg m-3 and viscosity 1.0 x 10-3...

A closed and elevated vertical cylindrical tank with diameter 2.00m contains water to a depth of...

A closed and elevated vertical cylindrical tank with diameter 2.00m contains water to a depth of 0.900m . A worker accidently pokes a circular hole with diameter 0.0190m in the bottom of the tank. As the water drains from the tank, compressed air above the water in the tank maintains a gauge pressure of5.00�103Pa at the surface of the water. Ignore any effects of viscosity. A. Just after the hole is made, what is the speed of the water as...

Question